HP ProBook 11 G1 - How to remove the top cover how to remove the keyboard – how to remove the HDD
HP ProBook 11 G1:
disassembling procedure
How
to remove the Battery
Remove
the battery:
1. Close the computer.
2. Turn the computer upside down with the front toward you.
3. Remove the two screw covers (1) that conceal the battery retention screws.
The battery screw covers are included in the Rubber Kit, spare part number 809868-001.
4. Loosen the two Phillips PM2.0×5.6 captive screws (2) that secure the battery to the computer.
5. Pivot the front edge of the battery (3) up and back until it rests at an angle.
6. Remove the battery (4).
1. Close the computer.
2. Turn the computer upside down with the front toward you.
3. Remove the two screw covers (1) that conceal the battery retention screws.
The battery screw covers are included in the Rubber Kit, spare part number 809868-001.
4. Loosen the two Phillips PM2.0×5.6 captive screws (2) that secure the battery to the computer.
5. Pivot the front edge of the battery (3) up and back until it rests at an angle.
6. Remove the battery (4).
How
to remove the Bottom cover
Before
removing the bottom cover, follow these steps:
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the battery
Remove the bottom cover:
1. Remove the following plugs that conceal the bottom cover screws:
(1) Four plugs in the corners of the computer
(2) Two plugs on the front edge of the computer
(3) Two plugs in the middle of the computer
The bottom cover screw covers are included in the Rubber Kit, spare part number 809868-001.
4. Remove the battery
Remove the bottom cover:
1. Remove the following plugs that conceal the bottom cover screws:
(1) Four plugs in the corners of the computer
(2) Two plugs on the front edge of the computer
(3) Two plugs in the middle of the computer
The bottom cover screw covers are included in the Rubber Kit, spare part number 809868-001.
2. Remove
the eight Torx8 T8M2.0×5.6 screws (4) that secure the bottom cover to
the computer.
3. Remove
the two Phillips PM2.0×3.7 broad head screws (5) that secure the
bottom cover to the computer in the battery bay.
4. Use
a case utility tool (1) or a similar thin, plastic tool to separate
the bottom cover from the base enclosure.
5. Swing
the front edge of the bottom cover (2) up and to the back until it
separates from the base enclosure.
6. Remove
the bottom cover (3).
How
to remove the Hard drive
Before
removing the hard drive, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
4. Remove the battery
5. Remove the bottom cover
Remove the hard drive:
1. Remove the four Phillips PM2.5×5.8 screws (1) that secure the hard drive to the base enclosure.
2. Slide the hard drive (2) forward until it disconnects from the system board.
5. Remove the bottom cover
Remove the hard drive:
1. Remove the four Phillips PM2.5×5.8 screws (1) that secure the hard drive to the base enclosure.
2. Slide the hard drive (2) forward until it disconnects from the system board.
3. Remove
the hard drive (3).
How
to remove the Solid-state drive
Before
removing the hard drive, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
4. Remove the battery
5. Remove the bottom cover
Remove the solid-state drive:
1. Remove the Phillips PM2.0×3.7 broad head screw (1) that secures the solid-state drive to the solid state drive tray. (The solid-state drive tilts up.)
2. Remove the solid-state drive (2) by pulling it away from the slot at an angle.
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
4. Remove the battery
5. Remove the bottom cover
Remove the solid-state drive:
1. Remove the Phillips PM2.0×3.7 broad head screw (1) that secures the solid-state drive to the solid state drive tray. (The solid-state drive tilts up.)
2. Remove the solid-state drive (2) by pulling it away from the slot at an angle.
3. If
it is necessary to replace the solid-state drive tray, remove the four Phillips
PM3.0×4.1 screws (1) that secure the solid-state drive tray to the
base enclosure.
4. Slide
the solid-state drive tray (2) forward until it disconnects from the
system board.
5. Remove
the solid-state drive tray (3).
The solid-state drive tray and screws are included in the Solid-State Drive Hardware Kit, spare part number 809859-001.
The solid-state drive tray and screws are included in the Solid-State Drive Hardware Kit, spare part number 809859-001.
How
to remove the Keyboard/top cover
Before
removing the keyboard/top cover, follow these steps:
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the battery
5. Remove the bottom cover
6. Remove the hard drive
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the battery
5. Remove the bottom cover
6. Remove the hard drive
Remove
the keyboard/top cover:
1. Release the ZIF connector (1) to which the keyboard cable is attached, and then disconnect the keyboard cable from the system board.
1. Release the ZIF connector (1) to which the keyboard cable is attached, and then disconnect the keyboard cable from the system board.
2. Release
the ZIF connector (2) to which the TouchPad button board cable is
attached, and then disconnect the TouchPad button board cable from the system
board.
3. Remove
the following screws that secure the keyboard/top cover to the base enclosure:
(1) One
Phillips PM2.0×3.7 screw on the front edge of the keyboard/top cover
(2) One Phillips PM2.0×3.7 broad head screw in the hard drive bay
(3) Six Phillips PM2.0×5.6 screws
(4) Two Phillips PM2.5×8.6 screws on the display hinges
(2) One Phillips PM2.0×3.7 broad head screw in the hard drive bay
(3) Six Phillips PM2.0×5.6 screws
(4) Two Phillips PM2.5×8.6 screws on the display hinges
4. Turn
the computer right side up with the front toward you.
5. Open
the computer as far as it will open.
6. Lift the front edge (1) of the keyboard/top cover until it separates from the front edge of the base enclosure.
7. Release the ZIF connector (2) to which the power button board cable is attached, and then disconnect the power button board cable from the system board.
8. Remove
the keyboard/top cover (3).
6. Lift the front edge (1) of the keyboard/top cover until it separates from the front edge of the base enclosure.
7. Release the ZIF connector (2) to which the power button board cable is attached, and then disconnect the power button board cable from the system board.