Lenovo ThinkPad X200 Tablet - X201 Tablet – AC adapter testing procedure – battery testing procedure – Backup battery testing procedure – Laptop repair and service
Category: Laptop Repair and Service
Contents of this article
- Power adapter testing procedure
- battery pack testing procedure
- Backup battery testing procedure
Lenovo ThinkPad X200 Tablet - X201 Tablet
Power system checkout
To verify a symptom, do the following:
1. Turn off the computer.
2. Remove the battery pack.
3. Connect the ac adapter.
4. Check that power is supplied when you turn on the computer.
5. Turn off the computer.
6. Disconnect the ac adapter and install the charged battery pack.
7. Check that the battery pack supplies power when you turn on the computer.
If you suspect a power problem,see the appropriate one of the following power supply checkouts:
“Checking the ac adapter”
“Checking operational charging”
“Checking the battery pack” on
“Checking the backup battery”
Checking the ac adapter
You are here because the computer fails only when the ac adapter is used.
If the power problem occurs only when the ThinkPadX200 Ultra Base isused, replace the Ultra Base.
If the power-on indicator does not turn on, check the power cord of the ac adapter for correct continuity and installation.
1. Unplug the ac adapter cable from the computer.
2. Measure the output voltage at the plug of the ac adapter cable. See the following figure
To verify a symptom, do the following:
1. Turn off the computer.
2. Remove the battery pack.
3. Connect the ac adapter.
4. Check that power is supplied when you turn on the computer.
5. Turn off the computer.
6. Disconnect the ac adapter and install the charged battery pack.
7. Check that the battery pack supplies power when you turn on the computer.
If you suspect a power problem,see the appropriate one of the following power supply checkouts:
“Checking the ac adapter”
“Checking operational charging”
“Checking the battery pack” on
“Checking the backup battery”
Checking the ac adapter
You are here because the computer fails only when the ac adapter is used.
If the power problem occurs only when the ThinkPadX200 Ultra Base isused, replace the Ultra Base.
If the power-on indicator does not turn on, check the power cord of the ac adapter for correct continuity and installation.
1. Unplug the ac adapter cable from the computer.
2. Measure the output voltage at the plug of the ac adapter cable. See the following figure
Note: Output voltage of pin no. 2 of the ac adapter may different from the
one you are servicing.
3. If the voltage is not correct, replace the ac adapter.
4. If the voltage is acceptable, do the following:
Replace the system board.
Note: Noise from the ac adapter does not always indicate a defect.
Checking operational charging
To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer.
4. If the voltage is acceptable, do the following:
Replace the system board.
Note: Noise from the ac adapter does not always indicate a defect.
Checking operational charging
To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer.
Perform operational charging. If the battery status
indicator or icon does not turn on, remove the battery pack and letitre turn to
room temperature. Reinstall the battery pack. If the charge indicator or icons till
does not turn on, replace the battery pack.
If the charge indicators till does not turn on, replace the system board. Then reinstall the battery pack. If it is still not charged, goto then extsection.
Checking the battery pack
Battery charging does not start until the Power Manager Battery Gauge shows that less than 96% of the total power remains; under this condition the battery pack can charge to 100% of its capacity. This protects the battery pack from being overcharged or from having a shortened life.
To check your battery,move your cursor to the Power Manager Battery Gauge icon in the icon tray of the Windows task bar and wait for a moment (but donot click),and the percentage of battery power remaining is displayed. To get detailed information about the battery, double-click the Power Manager Battery Gauge icon.
Note: If the battery pack become shot, it may not be able to charge. Remove it from the computer and leave it at room temperature for a while. After it cools down, reinstall and recharge it.
To check the battery pack, do the following:
1. Power off the computer.
2. Remove the battery pack and measure the voltage between battery terminals 1(+) and 7 (-). See the following figure
If the charge indicators till does not turn on, replace the system board. Then reinstall the battery pack. If it is still not charged, goto then extsection.
Checking the battery pack
Battery charging does not start until the Power Manager Battery Gauge shows that less than 96% of the total power remains; under this condition the battery pack can charge to 100% of its capacity. This protects the battery pack from being overcharged or from having a shortened life.
To check your battery,move your cursor to the Power Manager Battery Gauge icon in the icon tray of the Windows task bar and wait for a moment (but donot click),and the percentage of battery power remaining is displayed. To get detailed information about the battery, double-click the Power Manager Battery Gauge icon.
Note: If the battery pack become shot, it may not be able to charge. Remove it from the computer and leave it at room temperature for a while. After it cools down, reinstall and recharge it.
To check the battery pack, do the following:
1. Power off the computer.
2. Remove the battery pack and measure the voltage between battery terminals 1(+) and 7 (-). See the following figure
3. If the voltage is less than +11.0Vdc, the battery
pack has been discharged.
Note: Recharging will take at least 3 hours, even if the indicator does not
turn on.
If the voltage is still less than +11.0 Vdc after recharging replace the battery.
4. If the voltage is more than +11.0Vdc, measure the resistance between battery terminals 5 and 7.
The resistance must be 4 to 30KΩ. If the resistance is not correct, replace the battery pack. If the resistance is correct, replace the system board.
If the voltage is still less than +11.0 Vdc after recharging replace the battery.
4. If the voltage is more than +11.0Vdc, measure the resistance between battery terminals 5 and 7.
The resistance must be 4 to 30KΩ. If the resistance is not correct, replace the battery pack. If the resistance is correct, replace the system board.
Checking the backup battery
Do the following:
1. Power off the computer, and unplug the ac adapter from it.
2. Turn the computer upside down.
3. Remove the battery pack
4. Remove the backup battery
5. Measure the voltage of the backup battery. See the following figure
Do the following:
1. Power off the computer, and unplug the ac adapter from it.
2. Turn the computer upside down.
3. Remove the battery pack
4. Remove the backup battery
5. Measure the voltage of the backup battery. See the following figure
If the voltage is correct, replace the system
board.
If the voltage is not correct, replace the backup battery.If the backup battery discharges quickly after replacement, replace the system board