Water damage - LG Dishwasher LDS4821 – Error Codes – Wiring diagram
To lock/unlock the buttons, press QUICK and RINSE ONLY
simultaneously for 3 seconds. When CHILD LOCK is set, all buttons are disabled.
To cancel a running cycle, open the door, then press and hold the
POWER SCRUB and NORMAL buttons together for 3 seconds. The drain pump will be
activated and the cycle will be canceled.
Pressing the POWER button turns on power to the control. After the cycle is complete, the power
automatically switches off after 4 minutes for safety and economy. If there is an unusual Power surge or
disturbance, the power will be automatically turned off for safety and the
cycle will have to be started over.
Wiring Diagram
Click on the pictures to zoom in
ERROR MESSAGES
1E display => INLET ERROR: Not reached to the
normal water level in spite of 10 min. water supply.
The Water Supply Tap is closed.
The Water Supply is shut off.
The Inlet Hose is kinked.
The Water Pressure is very low. (below 10 psi)
Inlet Valve is OK?
The filter of Inlet Valve is clogged by impure water.
The Hall sensor is OK?
The Impeller of Air Guide is bound.
The Inlet Hose is kinked.
The Water Pressure is very low. (below 10 psi)
Inlet Valve is OK?
The filter of Inlet Valve is clogged by impure water.
The Hall sensor is OK?
The Impeller of Air Guide is bound.
Take action on Water Supply device.
Measure the electric resistance of Inlet Valve. (950-1300 )
Clean the filter of Inlet Valve.
Check the frequency of Inlet Water by the Test Mode.
Replace the Air Braker.
Measure the electric resistance of Inlet Valve. (950-1300 )
Clean the filter of Inlet Valve.
Check the frequency of Inlet Water by the Test Mode.
Replace the Air Braker.
0E
display => DRAIN ERROR: Not fully drained out in spite of 5 min. drain operation.
The Drain Hose kinked or blocked.
Wiring connection is OK?
The drain outlet of sump is blocked.
The Drain Pump/Motor or circuit is troubled.
Wiring connection is OK?
The drain outlet of sump is blocked.
The Drain Pump/Motor or circuit is troubled.
Remove the cause of kink or block.
Check the wiring connection.
Measure the electric resistance of Drain Motor. (20-40 )
Replace the Drain Motor or repair the Circuit.
Check the wiring connection.
Measure the electric resistance of Drain Motor. (20-40 )
Replace the Drain Motor or repair the Circuit.
E1 display => LEAKAGE
ERROR: The excessive RPM of Washing Motor happened during Wash cycle due
to water leakage.
Water leakage in Hose connections.
Water is leaked by damages.
The Motor Water Seal leakage of Sump assembly.
The height of Drain Hose connection (sink-Drain Hose) is not over 20″.
Impeller of the Washing Pump is worn away.
Water is leaked by damages.
The Motor Water Seal leakage of Sump assembly.
The height of Drain Hose connection (sink-Drain Hose) is not over 20″.
Impeller of the Washing Pump is worn away.
Replace the connections of Hose.
Check the point of damages and repair or replace the related parts.
Read the Installation Instructions and fix it to the recommended Height.
Replace the Impeller of the Washing Pump.
Check the point of damages and repair or replace the related parts.
Read the Installation Instructions and fix it to the recommended Height.
Replace the Impeller of the Washing Pump.
FE display => EXCESS
ERROR: Excessive water is supplied than normal water level.(Automatically
drain Pump operated.)
The Inlet Valve is troubled.
The Controller is troubled.
The Controller is troubled.
Replace the Inlet Valve.
Repair or replace the Controller.
Repair or replace the Controller.
tE display => THERMAL
ERROR: The resistance of thermistor not normally out put.
The Inlet Water Temperature is very high. (over 194 )
Wiring connection is OK?
The Thermistor is OK?
Wiring connection is OK?
The Thermistor is OK?
Check the temperature. (Test Mode).
If the temperature is displayed, adjust the Inlet Water Temperature
to 120.
If the temperature is not displayed, check the wiring connection. Check the electric resistance of Thermistor. (11~14k
at 77 )
Replace the PCB.
LE display => MOTOR
ERROR: The Motor is working abnormally.
Wiring connection is OK?
The Impeller of Washing Pump is locked.
The rotor of Washing Motor is locked.
The Blade is locked.
The Impeller of Washing Pump is locked.
The rotor of Washing Motor is locked.
The Blade is locked.
Check the wiring connection.
Replace the cause of restriction.
Replace the Washing Motor.
Replace the PCB.
Replace the cause of restriction.
Replace the Washing Motor.
Replace the PCB.
Test Mode LDS4821 Series dishwashers
