How to enter Service Mode - Adjustments - Firmware update - Initialize - Philips 50 inch Plasma TV - 50PFL4909
Service
Mode – Adjustments – Philips 50 inch (50”) Plasma TV – 50PFL4909
Service mode:
1. Turn the power on.
2. Press [0], [6], [2],
[5], [9], [6] and [INFO] buttons on the remote control unit in this
order. The following screen appears.
Purity
Check Mode
This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.
1. Enter the service mode.
2. Each time the [7] button on the remote control unit is pressed, the display changes as follows.
This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.
1. Enter the service mode.
2. Each time the [7] button on the remote control unit is pressed, the display changes as follows.
3.
To cancel or to exit from the Purity Check Mode, press [CH RETURN] or [PREV CH]
button.
White Balance Adjustment
The White Balance Adjustment should be performed when replacing the display Panel or Digital Main CBA.
Purpose: To mix red and blue beams correctly for pure white.
Symptom of Misadjustment: White becomes bluish or reddish.
1. Operate the unit for more than 30 minutes.
2. Enter the service mode.
3. Press [VOLUME DOWN]
button three times on the remote control unit to select “Drive setting”
mode. “Drive-” appears in the screen.
4. Set the color analyzer
at the CHROMA mode and zero point calibration. Bring the optical
receptor pointing at the center of the display-Panel.
[The optical receptor must be set perpendicularly to the LCD Panel surface.]
5. Press [3] button to select the “HDB” for High Drive Blue adjustment. (“HDB” appears in the screen.)
6. Press [MENU] button. The internal Raster signal appears in the screen.
7. Press [CHANNEL UP/DOWN] buttons to adjust the color temperature becomes 12000°K (x= 0.272 / y= 0.278 ± 0.003).
8. Press [1] button to
select the “HDR” for High Drive Red adjustment (“HDR” appears in the
screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color
temperature.
9. If necessary, adjust
the “HDB” or “HDR” again 10. Press [6] button to select the “MDB” for
Middle Drive Blue adjustment (“MDB” appears in the screen.) and press
[CHANNEL UP/DOWN] buttons to adjust the color temperature.
11. Press [4] button to
select the “MDR” for Middle Drive Red adjustment (“MDR” appears in the
screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color
temperature.
12. If necessary, adjust the “MDB” or “MDR” again.
13. Press [9] button to
select the “LDB” for Low Drive Blue adjustment (“LDB” appears in the
screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color
temperature.
14. Press [7] button to
select the “LDR” for Low Drive Red adjustment (“LDR” appears in the
screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color
temperature.
15. If necessary, adjust the “LDB” or “LDR” again.
16. Press [VOLUME DOWN]
button to shift to the “Debugging Message” mode. If there is no message
under “[WB]” section, this adjustment completes. If “Drive settings
are NG. Retry again.” Is displayed, repeat above steps from 5. to 15.
Then check “Debugging Message” again. If “Drive settings are NG. Retry
again.” is displayed, replace the display Panel or Digital Main CBA.
17. To cancel or to exit from the White Balance Adjustment, press [CH RETURN] or [PREV CH] button.
HOW
TO INITIALIZE THE LCD TV
The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized.
To put the program back at the factory-default, initialize the LCD TV using the following procedure.
NOTE: Disconnect any devic1. Turn the power on.
2. Enter the service mode. To cancel the service mode, press [Power ] button on the remote control unit.
3. Press [BACK] button to enter the Control Panel Key Confirmation Menu.
4. Press all buttons on the control panel.
5. Press [INFO] button to proceed with the self check mode.
6. Make sure to confirm the "INITIALIZED : OK" appears in the green screen.
7. Unplug the AC Cord and plug it back on again.
The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized.
To put the program back at the factory-default, initialize the LCD TV using the following procedure.
NOTE: Disconnect any devic1. Turn the power on.
2. Enter the service mode. To cancel the service mode, press [Power ] button on the remote control unit.
3. Press [BACK] button to enter the Control Panel Key Confirmation Menu.
4. Press all buttons on the control panel.
5. Press [INFO] button to proceed with the self check mode.
6. Make sure to confirm the "INITIALIZED : OK" appears in the green screen.
7. Unplug the AC Cord and plug it back on again.
FIRMWARE
RENEWAL MODE
Turn
the power off and unplug the AC Cord.
2. Insert the USB storage device to the USB port.
2. Insert the USB storage device to the USB port.
3.
Plug the AC Cord and turn the power on.
4. After few seconds, the menu mode will appear in the screen.
Note: After 30 seconds without an operation, the menu mode will disappear automatically.
To display the menu mode again, press the [MENU] button on the remote control unit.
5. Select “Setup” and press the [OK] button to display the setup menu.
6. Select “Software”.
7. Select “Software update”.
8. Select “USB”.
9. Press the [OK] button on the remote control unit to enter the update mode.
4. After few seconds, the menu mode will appear in the screen.
Note: After 30 seconds without an operation, the menu mode will disappear automatically.
To display the menu mode again, press the [MENU] button on the remote control unit.
5. Select “Setup” and press the [OK] button to display the setup menu.
6. Select “Software”.
7. Select “Software update”.
8. Select “USB”.
9. Press the [OK] button on the remote control unit to enter the update mode.
[Update
file selection screen appears as follows.
(Files included in the USB storage device are displayed.)]
Note: To cancel the update mode, select “Cancel” and press the [OK] button.
10.
Select the file and press [OK] button.
11. The update will start.
If the above screen isn’t displayed, repeat from step 1.
11. The update will start.
If the above screen isn’t displayed, repeat from step 1.
12.
Select “Yes” and press the [OK] button to update.
Note: Do not remove the USB storage device or turn the TV off while update is in
progress.
13. When the firmware update is completed it will be indicated on the screen.
13. When the firmware update is completed it will be indicated on the screen.
Turn the power off and turn the power on again.