Philips BDP3100, BDP3080, BDP5100 SMPS circuit diagram, Software upgrade - Blu-ray Disc Player

BDP3100/12/05/51/55/79/93/96/98/X78, BDP3080/98, BDP5100/12/05/51/93/98 Philips Blu-ray Disc Player - How to update the software, How to take the disc in emergency, Disc loader adjustments after repair

Loader repair Instruction for BDP3100,5100,3080/98

After scanning BARCODE on the new LOADER in supplier – TCL factory, print the one-dimensional code which generated by scanner and computer on label, then paste it into LOADER. If FA test passed, break off the protection point under the LOADER. Repair Procedure in workshop 1. In region’s workshop, to install loader in the machine then weld the open protection point.  Keep the set to connect the TV and power on, press keys “5” ”1” ”7” ”7” on Remote Control when in the HOME menu, then the menu will be displayed. 2. Select “Enter Barcode Info” from the menu, input the BARCODE of the LOADER and wait until the OSD displays “PASS”, press “STOP” key on Remote Control to go back to the menu. 3. Select “Laser check”, confirm whether the cable is connected and welded protection point is ok. 4. Restart the set, test CD, DVD, BD discs. If OK, the LOADER replacing procedure is finish.

How to take out the disc in emergency

If the tray can’t open in normal way or in the absence of power, you can make it through the instruction as below.

Note: Make sure to operate gently otherwise the guider would be damaged.

Software checks and upgrade

Preparation to upgrade software

1) Start the CD burning software & create a folder named "UPG_ALL",

2) Then copy the Bin file (BDP_3100_S_B.bin ) OR(BDP_5100_S_B.bin )into it,

3) Burn the data onto the blank CD or USB

4) If the model is BDP3100,must use (BDP_3100_S_X.bin )to upgrade If the model is BDP5100,must use (BDP_5100_S_X.bin )to upgrade X(A;B;C)If the model BD code is A,,X=A;BD code is B,X=B;BD code is C,X=C

A. Procedure for software upgrade

A) Upgrade software via Disc

1) Power on the set and insert the prepared Upgrade CDR

2. The set will start reading disc and response with the following display TV screen.

Now searching for the upgrade software, please wait….

                                       STILL

3) Press <OK> button to confirm, then screen will display :

An upgrade software has been found!

Start upgrade with version:WKXXX.X?

                        Cancel                   Start

4) Press Right cursor button to choose "Start", then press <OK>;

5) The software will upgrade and screen will display as below:

Upgrade is ongoing, Please wait…

Please do not unplug or switch off the device.

6) The screen will display as below when upgrading complete:

Upgrade has completed successfully!

Power off after 5s.

Power OFF

5) Restart the set.

SMPS (Power board) schematic and PWB

B) Upgrade software via network

1) Setup the network connection (See "Getting started">"Set up network").

2) In the Home menu, select <Setting> <Advanced Setup> <Software Download> <Network>.

* You are prompted to start upgrading processes if upgrade media is detected.

3) Follow the instructions on the TV screen to confirm update operation.

* Once software updated is complete, this player automatically turns off to standby.

4) Disconnect the power cord for a few seconds and connect again to turn on the player.

C) Update software via USB Flash Drive
1) Go to www.philips.com/support to check if the latest software
version is available for this player.
2) Download the software onto a USB flash drive.
3) Insert the USB flash drive to the USB jack of the rear panel.
4) In the Home menu, select <Setup> <Advanced Setup> <Software Updade > <USB>.
5) Follow the instructions on the TV screen to confrim update operation.
* Once software update is complete, this player automatically turns to standby.
6) Disconnect the power cord for a few seconds and connect again to turn on the player.

Read out the software versions to confirm upgrading

1) Power on the set and open the tray door.

2) Press <Home> button on the remote control

3) Select <Setup>, then press <OK>.

4) Select <Advanced Setup>, press right cursor to choose

<Version Info.>, then press <OK>, the software version and other information will display on the TV screen as below:

Model: BDP3XXX or   BDP5XXX

Versions:

http://www.philips.com/support

MAC:XX-XX-XX-XX-XX-XX

Caution The set must not be power off during upgrading; otherwise the Main board will be damaged entirely