Philips HTS3000 – Philips HTS3010 – Power Board (SMPS) Schematic – Adjustments
Home Theater System - Philips HTS3000 and HTS3010 - Adjustments - SMPS Schematic
System - Region Code - etc. Setting Procedure1) System Reset
a) press “system “ button on R/C,TV show “setup“
b) select the menu using the and on R/C
c) go preference page to do sysytem reset.
2) Region Code Change
a) Press the “stop” button on R/C in open model
c) Press 7 3 4 4 6 6 on R/C,then input desired number
To change region code
1 > USA
2 > EU
3 > AP
4 > Australia ,NZ , Latam
5 > Russia , INDIA
6 > CHINA
3)
Version Control Change
a) In open model, press “1“ “5“ “9“ on R/C
b) press “ok” button to com! rn
c) TV will show message as below:
a) In open model, press “1“ “5“ “9“ on R/C
b) press “ok” button to com! rn
c) TV will show message as below:
Current
model 3000-55/98/51/94/3010-94
Ver 00.18.00-70301-00 region : 4/3/5/5/3
Servo: OF.60.00.00
8032: 05.00.04.06 RISC:00.00.02.07
IF current model does not match you set use down arrow key on the remote to change.
4)
Password ChangeVer 00.18.00-70301-00 region : 4/3/5/5/3
Servo: OF.60.00.00
8032: 05.00.04.06 RISC:00.00.02.07
IF current model does not match you set use down arrow key on the remote to change.
a) press “system “ button on R/C,TV show “setup“
b) select the menu using the and on R/C
c) go preference page select “password“ to change
* 000000 is default password supplied.
b) select the menu using the and on R/C
c) go preference page select “password“ to change
* 000000 is default password supplied.
5)
Check on the Software Version
a)open the CD Door
b) press “display“ button on R/C
c) TV will show the version on screen.
a)open the CD Door
b) press “display“ button on R/C
c) TV will show the version on screen.
6)
Produce to Change Tuner Grid (only
applicable for certain regions)
In some countries ,the frequency step between adjacent channels in the (AM/MW)/FM band is 9kHz/50kHz (10kHz/100kHz in some areas).
a) press “source” to select “FM” or “AM”
b) In “FM” or “AM” playback mode, press & hold “play/pause” button until “Grid 9” or “Grid10” appears
note :repeating the same action will toggle back to it previous tuning grid setting.
* “grid 10” is default for /55/98/94 version, “grid 9” is default for /51 version and it doesn’t to change Tuner grid.
In some countries ,the frequency step between adjacent channels in the (AM/MW)/FM band is 9kHz/50kHz (10kHz/100kHz in some areas).
a) press “source” to select “FM” or “AM”
b) In “FM” or “AM” playback mode, press & hold “play/pause” button until “Grid 9” or “Grid10” appears
note :repeating the same action will toggle back to it previous tuning grid setting.
* “grid 10” is default for /55/98/94 version, “grid 9” is default for /51 version and it doesn’t to change Tuner grid.
7)
Upgrading new software
a) open the CD Door,then insert the CD-R program disc
b) close the DOOR
c) TV will show:
“loading“
pop message“upgrading“
“writing” about 2 minutes
“done “ * the latest upgraded is in version VER 00.18.00-70301-00
a) open the CD Door,then insert the CD-R program disc
b) close the DOOR
c) TV will show:
“loading“
pop message“upgrading“
“writing” about 2 minutes
“done “ * the latest upgraded is in version VER 00.18.00-70301-00