How to enter service mode Emerson lcd tv - EMERSON LC320EM81 lcd television Service mode – VBOM adjustment – Initialization – LCD Television repair and service
Category: LCD Television Service and repair
Contents of this article
- How to access Service mode
- VCOM adjustment
- Initializing the TV
- Power supply circuit
EMERSON LC320EM81
Service mode
How to set up the service mode
1. Use the service remote control unit. (Check the bottom of the page )
2. Turn the power on.
3. Press the service button on the service remote control unit
1. Use the service remote control unit. (Check the bottom of the page )
2. Turn the power on.
3. Press the service button on the service remote control unit
Purity Check Mode
This mode cycles through full-screen displays of red, green, blue, and white to
check for non-active pixels.
1. Enter the Service mode.
2. Each time pressing [7] button on the service remote control unit
1. Enter the Service mode.
2. Each time pressing [7] button on the service remote control unit
Note: When entering this mode, the default setting is White mode.
VCOM Adjustment
# This adjustment is required when reparing T-CON CBA
# This adjustment is required when reparing T-CON CBA
Note: Use the service remote control unit
1. Operate the unit for more than 20 minutes.
2. Set the color analyzer and bring the optical receptor to the center on the LCD-Panel surface after zero point calibration as shown above.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
3. Enter the Service mode.
4. Press [3] button on the remote control unit.
5. Press [CH. UP/ DOWN] buttons on the remote control unit so that the color analyzer value becomes minimum.
1. Operate the unit for more than 20 minutes.
2. Set the color analyzer and bring the optical receptor to the center on the LCD-Panel surface after zero point calibration as shown above.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
3. Enter the Service mode.
4. Press [3] button on the remote control unit.
5. Press [CH. UP/ DOWN] buttons on the remote control unit so that the color analyzer value becomes minimum.
White Balance Adjustment
*This adjustment is required when reparing T-CON CBA.
Purpose: To mix red, green and blue beams correctly for pure white.
Symptom of Misadjustment: White becomes bluish or reddish.
*This adjustment is required when reparing T-CON CBA.
Purpose: To mix red, green and blue beams correctly for pure white.
Symptom of Misadjustment: White becomes bluish or reddish.
1. Operate the unit for more than 20 minutes.
2. Input the White Purity.
2. Input the White Purity.
3. Set the color analyzer to the CHROMA mode
and bring the optical receptor to the center on the LCD-Panel surface after
zero point calibration as shown above.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
4. Enter the Service mode. Press [VOL. Down] button on the remote control unit and select “C/D” mode.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
4. Enter the Service mode. Press [VOL. Down] button on the remote control unit and select “C/D” mode.
5. [CUTOFF]
Press [3] button to select “COB” for Blue Cutoff adjustment. Press [1] button to select “COR” for Red Cutoff adjustment.
[DRIVE]
Press [6] button to select “DB” for Blue Drive adjustment. Press [4] button to select “DR” for Red
Drive adjustment.
6. In each color mode, press [CH. UP / DOWN] buttons to adjust the values of color.
7. Adjust Cutoff and Drive so that the color temperature becomes 12000K (x= 0.272 / y= 0.278 ±0.005).
Press [3] button to select “COB” for Blue Cutoff adjustment. Press [1] button to select “COR” for Red Cutoff adjustment.
[DRIVE]
Press [6] button to select “DB” for Blue Drive adjustment. Press [4] button to select “DR” for Red
Drive adjustment.
6. In each color mode, press [CH. UP / DOWN] buttons to adjust the values of color.
7. Adjust Cutoff and Drive so that the color temperature becomes 12000K (x= 0.272 / y= 0.278 ±0.005).
HOW TO INITIALIZE THE EMERSON LCD
TELEVISION
1. Turn the power on.
2. To enter the service mode, press the service button on the service remote control unit.
- To cancel the service mode, press [POWER] button on the remote control unit.
3. Press [INFO] button on the remote control unit to initialize the LCD television.
4. "INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initialzing is complete.
1. Turn the power on.
2. To enter the service mode, press the service button on the service remote control unit.
- To cancel the service mode, press [POWER] button on the remote control unit.
3. Press [INFO] button on the remote control unit to initialize the LCD television.
4. "INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initialzing is complete.
How to make the Service remote control unit
Cut “A” portion of the attached remote control unit as shown in Fig.
Cut “A” portion of the attached remote control unit as shown in Fig.
POWER SUPPLY SCHEMATIC DIAGRAM
