VESTEL - SOLARIS _ WASHING MACHINE _ SERVICE ASSISTANCE
TECHNICAL FEATURES
- Capacity : 5 kg, 6 kg, 7 kg, 7.5 kg
- Colour : White
- Spinning : 600 RPM, 800 RPM , 1000 RPM, 1200 RPM, 1400 RPM, 1600 RPM
- Voltage : 220-240 V
- Frequency : 50 Hz
- Ampere : 10 A
- Total electrical power : 2200 W
KEY COMPONENTS AND SPECIFICATIONS
DETERGENT BOX GROUP WORK PRINCIPLE
- PREWASH = WATER ENTRY VALVE 1
- MAIN = WATER ENTRY VALVE 2
- SOFTENER = WATER ENTRY VALVE 1 + VALVE 2
DISASSEMBLEY
- Remove two screws that fix the top-plate at the back.
- Push the top plate back and pull it up.
- Remove two screws that fix the door.
- Pull the door up
VESTEL - SOLARIS _ WASHING MACHINE _ DISASSEMBLE PROCEDURE
Remove 9 fixing screws that fix the door group.
- Remove the door inside plastic as shown in the picture.
- Remove the door hinge as shown in the picture.
- Remove the door glass as shown in the picture.
- Remove the door handle as shown in the picture.
- Remove the door handle prim as shown in the picture.
- Remove the door handle spring as shown in the picture.
- Remove the door lock tongue as shown in the picture.
- Remove the gasket as shown in the picture.
- Remove the gasket body fitting spring.
- Remove the detergent drawer and pull it up carefully.
- Remove the 5 screws which fix the control panel to the front panel.
- Remove 2 screws fixing the control panel.
- Remove one screw fixing the detergent box group.
- Pull the control panel up.
- Remove the wires as it shown the picture.
- Remove the screws fitting the electronic card.
- Remove the electronic card as shown in the picture.
- Remove the right part of the kick plate as it is shown in the picture.
- Remove the screw fixing the kick plate.
- Remove the kick plate as shown in the figure.
- Remove the 2 screws fixing the front panel at the bottom.
- Remove the 2 screws fixing the door lock.
- Push it down and remove the front panel.
VESTEL - SOLARIS _ WASHING MACHINE _ DISASSEMBLE PROCEDURE
MEDIUM SUPPORT PANEL
- Remove 4 screws fixing the panel.
- Remove the sub seal connector which is attached to the detergent drawer housing.
- Remove the wire that connected to the valve.
- Remove the valve connection.
- Remove the detergent drawer housing ass'y.
- Remove the wire that connected to the parasitic filter. Remove 2 screws fixing the filter.
- Remove the power cable group as it is shown in the picture.
- Remove the wire that connected to the pressure switch.
- Remove the pressure switch as it is shown in the picture.
- Remove the pressure switch hose handcuffs and pressure switch hose as it is shown in the picture.
- Remove the screw of door lock.
- Remove the wire that connected to the door lock.
- Remove the pipe clip that fixes the drain hose.
- Remove the pipe clip fixing the tub outlet hose.
- Remove the wire that connected to the pump motor.
- Remove the 4 screws fixing the pump motor.
- Remove the wire that connected to the heater.
- Remove the nut fixing the heater.
- Remove 4 screws fixing front counterweight on the front.
- Pull the counterweight back.
- Hold the gasket and gasket body fixing spring together, and pull them up.
- Remove two pins fixing the shock absorber.
- Remove the 2 screws fixing the upper counterweight.
- Remove the 4 screws fixing the spring hanger sheet iron.
- Remove the washing group as it is shown in the picture.
- Remove the insulating belt as it is shown in the picture.
- Insulating belt is used on the washing machines which do not have tub earth cable.
- There is a new label on the belts as seen below, indicating the insulating feature of the component.
- If belt will be ordered for the productions after 01.05.2008, the spare part orders should be done via the related production order part lists.
- Remove the screw fixing the driven pulley.
- Lay down the machine with an angel of 45° to the floor. Disconnect wires and remove the screws fastening the motor under the tub. Pull the motor up for disassembly.
- Remove 17 screws fixing the tub.
