MOTOROLA ATRIX 4G – DISASSEMBLING PROCEDURE – HOW TO REPLACE THE MOTHER BOARD – HOW TO RESET MOTOROLA ATRIX 4G

Motorola Atrix 4G – Disassembling procedure – How to replace the mother board – How to reset Motorola Atrix 4G

Motorola Atrix 4G

Motorola ATRIX 4G hard reset

To perform an External Manual Reset of your handset to restore to factory settings, follow the step:
1. Power off the phone, press and hold volume down button, press power button.
2. Screen will come up with "Fastboot", press Vol down key to cycle through choices until you get "Android Recovery", then press POWER key to select
3. Wait for the "triangle ! / Android" screen then go on to step 4
4. Press both Volume + and -. Tap on bottom right corner of the screen (may take a few times). a menu will come up.
5. Tap on "wipe data/factory reset", and tap OK. Another Confirmation screen will come. Tap Yes and OK
6. After userdata is cleared, the "reboot system now" option will be highlighted by Default. Tap OK.
7. Phone will reboot to initial setup MOTOBLUR screen.

Please note: If Factory menu does not appear press the volume-button to access the menu.
Navigation in menu by volume up/down, confirm with power button.

Factory Data Reset through settings menu

1.Open the Applications Tray. (arrow pointing up located in the middle at the bottom of the display screen)
2.Touch Settings
3.Touch Privacy
4.Touch Factory data reset
5.Touch Reset Phone
6.Touch Erase Everything

MOTHER BOARD REPLACEMENT PROCEDURE 

Pry the rear cover from the back of the phone.

Insert a spudger or plastic opening tool into the small notch at the base of the battery.

Lift the battery out of the phone.

Remove the four 5.0 mm T5 Torx screws from the corners of the phone.

Remove three 5.5 mm T5 Torx screws from the back of the phone.
Lift up the black rubber flap near the SD card slot.
Remove the single 5.5 mm T5 Torx screw beneath the flap.
Do not attempt to loosen the screws with too much force. These screws are small, and easily stripped.

Remove the back case of the phone by gently lifting the tabs located on top of the phone near the lock button.

Use the case opener or spudger in these small areas because the plastic tabs can be easily broken.
Lift the tabs located on the bottom of the phone to continue removing the back cover.

Slide an opening tool between the gap from the back of the case to the front.

After separating the sides, make sure there is a noticeable gap between the back case and the rest of the phone.
After detaching the tabs and sliding down the sides, there should be a noticeable gap between the front and back cases.

Carefully separate the back case from the rest of the phone by lifting it away from the phone.

Do not completely remove the case from the rest of the phone. The antenna is connected to both cases.

Disconnect the antenna from its housing on the motherboard by gently lifting beneath it.

Ease the antenna from out of its guide along the side of the phone

Once the antenna is detached, remove the back case and the antenna from the phone
The antenna is soldered to the back case. Do not pull with too much force.

To remove the motherboard, first dislodge the right side of the motherboard, where the external connections are located, from the rest of the phone.

This can be done by placing a spudger in between the two ports on the phone, between the black plastic and motherboard, and prying out.
The motherboard should be able to be easily lifted upwards after dislodging it.
If the white rubber piece moves, replace it where it came from upon reassembly.

First, several connections must be disconnected to completely separate the motherboard from the rest of the phone.

The connection highlighted with a red box must be pulled down instead of out.
Using the spudger tool, separate the two connections on the motherboard highlighted with orange circles by pulling them out.
The black switch on top of this connection acts as a lock. Push it forwards to unlock the connection.

After disconnecting the motherboard, there should be five distinct and separate parts of the phone: back cover, back case, front case, battery, and motherboard.