TOSHIBA 46H84_51H84_57H84_46H84C_51H84C_57H84C - HOW TO ADJUST CONVERGENCE
Universal Remote Control Set-up Codes to Toshiba brand TVs - With different brand remote controls: 0018 0025 0039 0044 0045 0075 0101 0119 0128 0141 0143
0145 0165 0195 0227 0247 0369 0379 0460 0642 0658 0713
0810 0813 0814
Convergence Adjustment Details to Toshiba PTVs - 46H84_51H84_57H84_46H84C_51H84C_57H84C
> Receive NTSC signal.
> Enter to the service mode.
(Service Mode entry details; by previous post here)
RCUT
40H
* Press "7" button to
enter the convergence adjusting mode, and the internal net pattern will be
displayed.
* Then, press "9" button
to display vertical stripes.
* Select the point and the colour by
pressing following buttons. (Cursor should be blinking.)
"2", "8",
"4", "6" : To select point.
“3" : To select colour.
* Then press "5" button,
and adjust the convergence by pressing following buttons. (Cursor should not be
blinking.)
"2", "8",
"4", "6" : To adjust convergence.
"3" : To select colour.
* Repeat from steps 3 to 4 until
the convergence and the geometry become fine.
* Press "7" button to
memorize the adjusted data.
> Message of "PLEASE PUSH
TOUCH FOCUS" will be displayed, and press TOUCH FOCUS button which is
located on the front panel.
> TOUCH FOCUS CALIBRATION will
start.
> Soon message of "CALIBRATION
FINISHED" will be displayed, and then a normal picture will be displayed.
> Push TOUCH FOCUS button again,
and confirm that the convergence does not change.
> If message of "TOUCH FOCUS
ERROR" is displayed, check the connection between four sensors and
Convergence Unit.
> Check the geometry of internal
net pattern.
> If any problem cannot be found,
hardware might have problem.
EXPLANATION OF KEY-FUNCTION IN
THE CONVERGENCE ADJUSTMENT MODE
Load BACK UP DATA
|
1 button
|
Up :
|
2 button
|
Select Green color
|
3 button
|
Left
|
4 button
|
Blinking of cursor ON/OFF
|
5 button
|
Right
|
6 button
|
Adjust mode ON/OFF
|
7 button
|
Down
|
8 button
|
Vertical stripe ON/OFF
|
9 button
|
Erase Green line
|
0 button
|
Erase Red line
|
100 button
|
Erase Blue line
|
ENT button
|
The following message will appear
while pressing "1" button.
* ENTER: TO LOAD BACKUP DATA
* MUTE: TO LOAD INITIAL DATA
* EXIT: TO EXIT
BACKUP DATA sets in factory by
performing CALIBRATION. BACKUP DATA updates by performing CALIBRATION again.
INITIAL DATA uses the seed data on this model. Thus, it cannot updates. INITIAL
DATA is not adjusted. Therefore, convergence data operates incorrectly.
Normally, BACKUP DATA operates as base data on this model. If BACKUP DATA is
incorrectly operated, INITIAL DATA is operated instead of BACKUP DATA In many
cases, colour mis-convergence may be corrected by returning HIT and WID data in
main deflection side to initial adjusting values. Following cases will surely
require readjustment of convergence.
Convergence_46_51_57 Wide.
Focus adjustment
(Condition)
* User Adjustment : SPORTS
(CONTRAST MAX, BRIGHTNESS CENTRE)
* Adjust after Cantering Magnet
adjusts
* Signal : Lens Focus : R Dot
cross (NTSC)
G Dot cross (NTSC)
B Dot cross (NTSC)
Electrical Focus : R Dot cross
(NTSC)
G Dot cross (NTSC)
B Dot cross (NTSC)
Adjustment
1. Common Items
1) Rough Adjust the lens focus
and electrical focus of each color(R, G, B)
2. Green Adjustment
1) Receive green single colour by
shielding jig.
2) Receive the Dot Cross pattern.
3) Adjust Green electrical focus.
Adjust Green electrical focus VR
on focus pack (Z410) for best centre focus.
If the focus blur on screen centre and circumference, adjust the
electrical focus is best point on all of screen.
4) Adjust Green lens focus.
Receive the Dot Cross pattern.
Adjust Green lens for best centre focus.
Green lens focus adjustment
target
Dot-cross has red flare (red
flare width :1mm)
5) Repeat (3)~(4),and adjust best
focus point.
Red Adjustment
1) Receive Red single colour by shielding
jig.
2) Receive the Dot Cross pattern.
3) Adjust Red electrical focus.
Adjust Red electrical focus VR on
focus pack (Z410) for best centre focus.
4) Adjust Red lens focus. Receive the Dot Cross pattern. Adjust Red
lens for best centre focus.
5) Repeat (3)~(4),and adjust best
focus point.
Blue Adjustment
1) Receive Blue single colour by
shielding jig.
2) Receive the Dot Cross pattern.
3) Adjust Blue electrical focus.
Adjust Blue electrical focus VR
on focus pack (Z410) for best centre focus.
(The Brightness is minimum point of Blue.)
Adjust Blue lens focus.
> Receive the Dot Cross pattern.
Adjust the Blue lens for best centre focus.
> After easy lens adjustment, turn
to right side lens focus screw, and so dot-cross has flare.
> Next turn left focus screw, so
flare disappears in Dot-Cross and Dot-Cross become blur.
> This point is blue lens focus
adjustment target. (Flare disappears and become blur)
CRT REPLACEMENT
When CRT is replaced, main
deflection readjustment and colour matching are required.
Perform following procedures.
1. Replace two CRT’s of blue and
red.
2. Perform horizontal adjustment
for blue and red yokes on base of green CRT data. Mount yoke and velocity mod.
coil alignment, pushing towards CRT without gap.
3. Adjust alignment of blue and
red. (Refer Alignment adjustment for details.)
4. Rotating entering magnet,
adjust CRT centres of red and blue to CRT centre of green. (Picture position
adjustment)
5. Adjust HIT and WID data of
main deflection, and decide data at the most precise screen comparing to green
data.
6. Adjust convergence of screen
picture for colour matching. Do not move green one at this time.
7. After convergence adjustment
of screen picture finishes, replace green CRT.
For green CRT as well, repeat
steps 2 to 5 above on bases of red and blue colour matching to adjust
convergence.
8. Execute TOUCH FOCUS following
instructions displayed on the screen after finishing convergence adjustments of
all the colours.
Note: Press button "7"
again after "PLEASE PUSH TOUCH FOCUS" has been displayed. Then, TOUCH
FOCUS will not be executed, and the current state of convergence will be
displayed.