Technical description and composition of the SAMSUNG T31D310EW TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: T31D310EW
Panel: CY-HH032AGSV1H
T-CON: LK315T3HC1
LED driver (backlight): integrated into PSU; 76V 450mA
PWM LED driver: 7014X
Power Supply (PSU): BN44-00696A
PWM Power: S3330 (FAN6755)
MainBoard: BN41-02098B - BN94-08002Q
IC MainBoard: Spi-25Q40CLSIP, NTP7414, DRV612
Tuner: BN40-00282A (DT0S40EIH276A)
Control: BN59-00741A
Appearance
SAMSUNG T31D310EW
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG T31D310EW TV does not turn on, does not respond to the remote control and control panel buttons, indicators do not light up and do not blink.
With such manifestations, a malfunction is most likely to be detected in the BN44-00696A power supply module. It is necessary to verify the presence of its output voltages and, if they are completely absent, check the power switches and rectifier diodes for a probable short circuit.
In the event of a breakdown in the secondary circuits of the converter, it can usually fail in short circuit mode, and in the event of a short circuit in the power elements of the primary circuit, the main fuse or current sensor at the source of the key most often breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, power supply, frequency-setting, damper ... as well as elements of the Negative Stabilization Feedback. The PWM chip can also cause a malfunction of the power switch of the converter and is checked by replacement.
- There is no image, but there is sound, it responds to the remote. Or the image appears when you turn on and immediately disappears
In such cases, the most likely malfunction of the backlight elements of the LED panel. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
To detect a break in the LED lines without disassembling the panel, a current source is required. It is impossible to open transitions connected in series with a simple multimeter; voltage of several tens of volts is necessary.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the BN41-02098B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). Often, the MB (SSB) card must be replaced in case of complex malfunctions that are difficult to detect. When trying to repair, you should check its elements - Spi-25Q40CLSIP, NTP7414, DRV612 and replace failed chips with new ones. Some malfunctions may be due to the use of BGA soldering technologies in modern Main Board. Typically, such defects are detected by local heating of the chip.
Before replacing the tuner BN40-00282A (DT0S40EIH276A), if there is no tuning for the channels, you must first check the software and the supply voltage at its terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus
It should be remembered! Attempts to self-repair a SAMSUNG T31D310EW TV, in the absence of the necessary qualifications and experience, are categorically not recommended and are fraught with negative consequences, up to the complete non-serviceability of the device!
FIRMWARE FOR SPI FLASH ----------> SAMSUNG T31D310EW , Main: BN41-02098B - BN94-08002Q, Panel: CY-HH032AGSV1H
The appearance of the MainBoard BN41-02098B is shown in the figure below:
BN41-02098B
BN41-02098B can be used in TVs:
SAMSUNG UE32H4270AU UE32H4270 (Panel HH032AGH-R1), SAMSUNG LT24D310ES (Panel V236BJ1-LE2), SAMSUNG UE40H5000AK (Panel CY-GH040BGLV1V), SAMSUNG UE48H5270AU UE48H5270 (Panel CY-GH048BGLV1V), SAMSUNG UE32H4290AU UE32H4290 (Panel HH032AGH-R2), SAMSUNG UE40H5290AU UE40H5290 (Panel CY-GH040BGLV1V), SAMSUNG UE40J5000AU UE40J5000 (Panel CY-JJ040BGNV2V), SAMSUNG UE40H5020 UE40H5020AK (Panel CY-GH040BGSV1V), SAMSUNG UE40J5100AU (Panel CY-GH040BGSR1V), SAMSUNG T31D310EW (Panel CY-HH032AGSV1H), SAMSUNG UE48J5000AU (Panel CY-JJ048BGEV5V), SAMSUNG UE32H5020AK (Panel CY-GH032BGLV4V), SAMSUNG UE40J5120AU (Panel CY-GH040BGSV1V), SAMSUNG LT32E310EX T32E310EX (Panel CY-GJ032BGEV1V), SAMSUNG UE40H5270 UE40H5270AU (Panel CY-GH048BGLV1V), SAMSUNG UE32J5100AK UE32J5100 (Panel CY- GH032BGSV1V), SAMSUNG UE32H5000AK UE32H5000 (Panel CY-GH032BGLV1V), SAMSUNG UE48H5000 UE48H5000AK (Panel CY-GH048CSLV1V), SAMSUNG UE32J5120AK UE32JSV1B (CY.
The appearance of the power supply
Main features of the SAMSUNG T31D310EW device:
Installed matrix (LED panel) CY-HH032AGSV1H.
The matrix control uses the Timing Controller (T-CON) LK315T3HC1.
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by a 7014X PWM controller.
The necessary supply voltages for all nodes of the SAMSUNG T31D310EW TV are generated by the power module BN44-00696A, or its analogs using S3330 microcircuits (FAN6755).
MainBoard - the main board (motherboard) is a BN41-02098B module, using Spi-25Q40CLSIP, NTP7414, DRV612 and others.
The tuner BN40-00282A (DT0S40EIH276A) provides the reception of television programs and tuning to channels.