Technical description and composition of the SAMSUNG LE32E420E2W TV, panel type and applicable modules. The composition of the modules.SAMSUNG
Model: LE32E420E2W LE32E420
Chassis / Version: U71C
Panel: LTF320AP13
Lamp backlight: 3 Lamp CCFL
T-CON: 32AP11S4L V1.1; BD8193MWV, MAX9694
Inverter (backlight): SST320_3UA01
Power Supply (PSU): BN44-00468A
PWM Power: SEM2106, STR-W6052S
MainBoard: BN41-01795A BN94-05680B
IC MainBoard: K9F1G08UOD, 25Q40BVSIP, S24C256, WT61P805, NTP7412S
Tuner: DT0D40FVL084AA - BN40-00231A
Control: AA59-00602A
Specifications LE32E420
SAMSUNG LE32E420E2W
General repair guidelines for TV LCD
Possible manifestations of defects
- SAMSUNG LE32E420E2W does not turn on. There is no reaction to the remote control and to the control buttons from the front panel. Indicator lights do not light or flash.
Typically, with such manifestations, the defect is caused by faulty elements in the BN44-00468A power module. It is necessary to measure its secondary output voltages, and in case of their absence, check the serviceability of the power switches of the converters and rectifier diodes for a short circuit.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during a short circuit in the elements of the primary circuit, the mains fuse usually breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. It can be supply, damper circuits, or elements of OOS (negative feedback) stabilization. The reason for the breakdown of the power switch may be PWM (PWM) SEM2106, STR W6052S. It is checked only by replacement with a known good one.
- There is no image, but there is sound and reaction to commands from the remote control. Or the image appears immediately after turning on and disappears.
These manifestations can be triggered by a power supply module, or by inverter defects, as well as distortion of the currents in the lamps due to their uneven wear. After checking all the electrolytic capacitors of the filters that are involved in the power supply of the inverter, it is necessary to ring in its converter the power switches for breakdown and the secondary windings of the transformers for an open.
If in diagnosing a malfunction, it is necessary to disable the inverter protection, there is a risk of failure of the power elements of the inverter, and special care is required during operations, and after their completion, it is necessary to restore the protection circuits for further safe operation of the TV by the owner in normal mode.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the BN41-01795A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). Sometimes it is necessary to check or replace (if necessary) the elements of the MainBoard board - K9F1G08UOD, 25Q40BVSIP, S24C256, WT61P805, NTP7412S. In cases where the BGA processor is used, its malfunction is usually detected by the local heating method.
Before replacing the tuner DT0D40FVL084AA - BN40-00231A, if there is no tuning for the channels, you must first check the software and the supply voltage at its terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus
We recommend LE32E420E2W TV owners to be repaired only by qualified specialists with the necessary work experience! Attempts to repair it yourself without the appropriate knowledge and skills can lead to irreversible negative consequences!
FIRMWARE ---> SPI FLASH SAMSUNG LE32E420E2W U71C, Main: BN41-01795A BN94-05680B, Panel: LTF320AP13.
SAMSUNG LE32E420M2W - Panel: LTF320AP13, Main: BN94-05680B BN41-01795A, PSU: BN44-00468A, Inverter: 32T3UC SST320-3UA01
The appearance of the MainBoard BN41-01795A is shown in the figure below:BN41-01795A
BN41-01795A can be used in TVs:
SAMSUNG UE32EH4000 UE32EH4000W (Panel LTJ320AP03-L), SAMSUNG UE32EH5000W (Panel DE320BGM-C1), SAMSUNG UE26EH4000W (Panel T260XVN01.1), SAMSUNG UE32EH5007K UE32EH5007 (Panel LTJ320HN07-L), SAMSUNG UE32EH5047K UE32EH5047 (Panel DE320BGA-B1), SAMSUNG UE40EH5007K (Panel CY-DE400BGSV1L), SAMSUNG UE32EH5057K (Panel DE320BGA-B1), SAMSUNG UE40FH5007K (Panel CY-DF400BGLV1V), SAMSUNG UE40EH5047K (Panel LTJ400HM08-L), SAMSUNG UE40EH5057K UE40EH5057 (Panel CY-DE400BGSV1L), SAMSUNG UE40EH5050W UE40EH5050 (Panel CY -DE400BGSV1L), SAMSUNG UE40EH5000 UE40EH5000W (Panel LTJ400HM801-V), SAMSUNG UE32EH5000K UE32EH5000 (Panel LTJ320HN07-L), SAMSUNG UE32EH5000W UE32EH5000 (Panel DE320BGM-C1), SAMSUNG LE32E420E2W LE32E420 (Panel LTF320AP13), SAMSUNG UE32EH4030 UE32EH4030W (Panel DE320AGH-C2 ), SAMSUNG UE46EH5057K UE46EH5057 (Panel LTJ460HN05-L), SAMSUNG UE40EH5040 UE40EH5040W (Panel CY-DE400BGSV1L).
The appearance of the power supply
Main features of the SAMSUNG LE32E420E2W device:
Installed matrix (LCD-panel) LTF320AP13.
The matrix control uses the Timing Controller (T-CON) 32AP11S4L.
To power the backlight used inverter SST320_3UA01.
The necessary supply voltages for all nodes of the SAMSUNG LE32E420E2W TV are generated by the BN44-00468A power module or its analogs using SEM2106, STR-W6052S microcircuits.
MainBoard - the main board (motherboard) is a BN41-01795A module, using microchips K9F1G08UOD, 25Q40BVSIP, S24C256, WT61P805, NTP7412S and others.
Tuner DT0D40FVL084AA - BN40-00231A provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: SAMSUNG
Model: LTF320AP13
Type: a-Si TFT-LCD, Panel
Diagonal size: 31.5 inch
Resolution: 1366x768, WXGA
Display Mode: PVA, Normally Black, Transmissive
Active Area: 697.685x392.256 mm
Surface: Antiglare (Haze 5.5%), Hard coating (2H)
Brightness: 300 cd / m²
Contrast Ratio: 3500: 1
Display Colors: 16.7M (8-bit), CIE1931 72%
Response Time: 8 (G to G)
Frequency: 60Hz
Lamp Type: 3 pcs CCFL Embedded (Balance board)
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 12.0V