Technical description and composition of the SAMSUNG LE40A556P1F TV, panel type and applicable modules. The composition of the modules.SAMSUNG
Model: LE40A556P1F
Chassis / Version: CN07 // GPR40SEN
Panel: V400H1-L03 REV C1
T-CON: V400H1-C03
Inverter (backlight): T871034.021 CEM-1-97 I400H1-20C-A011C
Power Supply (PSU): BN44-00199A IP-211135A
PWM Power: FAN7530, QM853 STM4472, FSQ0765RG, LX1692BIDW, 74VHC123A
MainBoard: BN41-00974B BN94-01656M
IC MainBoard: MT8226, MT8291E, NTP-3100, WT61P8, SDP72, D61211GM, HYB25DC256163CE-4, K4T56163QT, TMDS351
Tuner: BN40-00120A
Control: IR: BN41-00922A
Technical Specifications LE40A556P1F
SAMSUNG LE40A556P1F
General repair guidelines for TV LCD
Possible malfunctions
- SAMSUNG LE40A556P1F TV does not turn on, does not respond to the remote control and control panel buttons, indicators do not light up and do not blink.
In some of these cases, a fault is detected in the BN44-00199A power supply module. Then it is necessary to measure its output voltage and, in case of their complete or partial absence, it is necessary to check the serviceability of power switches and rectifier diodes of the converters for the presence of a possible short circuit.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during a short circuit in the elements of the primary circuit, the mains fuse usually breaks.
Mos-Fet power switches, used in switching power supplies, sometimes fail due to a malfunction of any other elements that can put it out of operation in key mode or create an excess of the maximum permissible parameters of the switch. These can be elements supplying the PWM controller, frequency-setting or damping circuits, or negative feedback elements in the stabilization circuit. PWM controllers FAN7530, QM853 STM4472, FSQ0765RG, LX1692BIDW, 74VHC123A, in the absence of visible damage or obvious short-circuit between the terminals, are checked by replacing with new ones, or obviously working.
- There is no image, there is sound, it responds to the remote control, the channels are switched. In some cases, the image appears when you turn on and immediately disappears.
These manifestations can be triggered by a power supply module, or by inverter defects, as well as distortion of the currents in the lamps due to their uneven wear. After checking all the electrolytic capacitors of the filters that are involved in the power supply of the inverter, it is necessary to ring in its converter the power switches for breakdown and the secondary windings of transformers for an open.
Sometimes, for diagnostic purposes, inverter protection must be disabled. In such cases, special care must be taken during work, and the protection circuits should be restored immediately after the repair is completed.
- The TV does not turn on, the indicator signals standby or working mode, or blinks.
Repair or diagnostics of the BN41-00974B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its chips MT8226, MT8291E, NTP-3100, WT61P8, SDP72, D61211GM, HYB25DC256163CE-4, K4T56163QT, TMDS351 and other possible faulty components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
Service manual and schematic diagram ----> SAMSUNG LE40A556 Chassis GPR40SEN.
PSU SCHEMATICS ----> BN44-00199A Power supply.
If the TV works normally from external devices, but does not tune into television channels, the tuner BN40-00120A may be malfunctioning. In such cases, first of all, you should make sure that there are supply voltages at its corresponding terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus. Sometimes the cause of the inoperability of the tuner may be a software failure.
Attention! For users and owners of LE40A556P1F TVs who do not have the appropriate qualifications, knowledge and experience, we categorically do not recommend attempting self-repair in order to avoid negative consequences that could lead to complete non-repairability of the device.
The appearance of the MainBoard BN41-00974B is shown in the figure below:BN41-00974B
BN41-00974B can be used in TVs:
SAMSUNG LE32A556P1 LE32A556P1F (Panel LTF320HA01 A04), SAMSUNG LE37A552 LE37A552P3R (Panel T370HW02 V.4), SAMSUNG LE37A656A1 LE37A656A1FXRU (Panel T370HW02 V6), SAMSUNG LE32A558P3F (Panel LTF320HA01), SAMSUNG LE40A656A1F (Panel LTF400HC01 A02), SAMSUNG LE37A615A3F LE37A615 (Panel T370HW02 V.4), SAMSUNG LE40A556P1F (Panel V400H1-L03 REV C1), SAMSUNG LE40A558P3F LE40A558 (Panel LTF400HA03), SAMSUNG LE32A656A1F (Panel LTF320HA04).
The appearance of the power supply
Main features of the SAMSUNG LE40A556P1F device:
Installed matrix (LCD panel) V400H1-L03 REV C1.
The matrix control uses the Timing Controller (T-CON) V400H1-C03.
To power the backlight used inverter T871034.021.
The necessary supply voltages for all nodes of the SAMSUNG LE40A556P1F TV are generated by the BN44-00199A power supply module or its analogs using FAN7530, QM853 STM4472, FSQ0765RG, LX1692BIDW, 74VHC123A microcircuits.
MainBoard - the main board (motherboard) is a BN41-00974B module, using microcircuits MT8226, MT8291E, NTP-3100, WT61P8, SDP72, D61211GM, HYB25DC256163CE-4, K4T56163QT, TMDS351 and others.
The tuner BN40-00120A provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: CMO
Model: V400H1-L03
Type: a-Si TFT-LCD, Panel
Diagonal size: 40 inch
Resolution: 1920x1080, FHD
Display Mode: MVA, Normally Black, Transmissive
Active Area: 885.6x498.15 mm
Surface: Antiglare (Haze 17%), Hard coating (3H)
Brightness: 500 cd / m²
Contrast Ratio: 4000: 1
Display Colors: 16.7M (8-bit), CIE1931 72%
Response Time: 6.5 (G to G)
Frequency: 60Hz
Lamp Type: 20 pcs CCFL Embedded (Balance board)
Signal Interface: LVDS (2 ch, 8-bit), 51 pins
Voltage: 12.0V