Technical description and composition of the PHILIPS 32PFL6008T TV, type of panel and applicable modules. The composition of the modules.PHILIPS LED
Model: 32PFL6008T / 60
Chassis / Version: QFU2.1E LA
Panel: LC320EUF (FE) (P1) code 423
LED driver (backlight): integrated into PSU
PWM LED driver: OZ9909TN
Power Supply (PSU): PLDD-P109A - 272217190609 2722 171 90609
PWM Power: L6599 (PWM Resonant), FSL106HR (Standby DIP-8)
MainBoard: 310431365664 310432868323 3104 313 65664 3104 328 68323
IC MainBoard: FUSION120, H5TQ2G83BFR, H26M21001ECR, TAS5731P1
Tuner: SUT-RE214AN
Specifications 32PFL6008T
PHILIPS 32PFL6008T
General repair guidelines for TV LCD LED
PHILIPS 32PFL6008T / 60, like other televisions, it is advisable to start repairing with a careful examination of the external and internal elements and modules. Specific external damage to some elements can sometimes indicate further actions to determine the malfunction of the TV and localize the defect before the necessary measurements are taken. Ring cracks in the soldering of the leads of the heating elements, swollen electrolytic capacitors, a charred paint layer on the resistors - all this for the repairman can be a significant clue in the assumptions about the causes and consequences of the malfunction.
Malfunctions of the power module can be expressed in different ways, for example, the PHILIPS 32PFL6008T does not turn on at all and the control lamps on its front panel do not light up and do not blink, and there are no signs of operability. It should be noted that with the same external manifestations, the processor power regulator (converter) may be faulty. It is advisable to start the troubleshooting of the power supply module by checking the state of the electrolytic capacitors of the rectifier filters and the mains fuse. Defective capacitors should be replaced. If the mains fuse is broken, it is necessary to check first of all the power semiconductor elements - rectifier diodes and transistors, which are often found in such a state of breakdown.
Mos-Fet keys used in switching power supplies (SMPS) rarely fail for no reason to look for when checking other circuit elements. Often the breakdown is caused by malfunctions of electrolytic capacitors or semiconductor elements in the primary circuit, or by a break in the resistors in the stabilization circuits. The PWM controller chip can also cause a breakdown of the power switch of the converter.
Sometimes the PHILIPS 32PFL6008T TV does not have an image, but there is sound, or the image appears and immediately disappears. In this case, there is a high probability of a malfunction of the converter for the panel backlight LEDs code 423, or a break in the LED circuit is possible. In such cases, first of all, it is necessary to verify the serviceability of all the electrolytic capacitors of the filter by supplying the LED driver itself, including in the power supply unit (power supply unit).
Often in the absence of backlighting, disassembling the panel is required. It is necessary to check the serviceability of the transitions of the LEDs, as well as the reliability of the contact connections in the rulers and connectors.
To detect a break in the LED lines without disassembling the panel, a current source is required. It is impossible to open transitions connected in series with a simple multimeter; voltage of several tens of volts is necessary.
Attention! For users and owners of 32PFL6008T TVs who do not have the appropriate qualifications, knowledge and experience, we strongly recommend against self-repair attempts to avoid negative consequences that could lead to complete non-repairability of the device !!
Service manual and schematic diagram 32PFL6008T/60 Chassis QFU2.1E LA
Chassis QFU2.1E LA FOR MODELS: 32PFL6007H/12, 32PFL6007K/12, 32PFL6007T/12, 32PFL6087H/12, 32PFL6087K/12, 32PFL6087T/12
37PFL6007H/60, 37PFL6007H/12, 37PFL6007K/12, 37PFL6007T/12, 37PFL6777H/12, 37PFL6777K/12
42PDL6907H/12, 42PDL6907K/12, 42PDL6907T/12, 42PFL6007H/12/60, 42PFL6007K/12, 42PFL6007T/12/60, 42PFL6057H/12/60, 42PFL6057K/12, 42PFL6057T/12/60, 42PFL6067H/12/60, 42PFL6067K/12, 42PFL6067T/12/60, 42PFL6097H/12/60, 42PFL6097K/12, 42PFL6097T/12/60, 42PFL6687H/12/60, 42PFL6687K/12, 42PFL6687T/60, 42PFL6877H/12/60, 42PFL6877K/12, 42PFL6877T/12/60
47PDL6907H/12, 47PDL6907K/12, 47PDL6907T/12, 47PFL6007H/12/60, 47PFL6007K/12, 47PFL6007T/12/60, 47PFL6057H/12/60, 47PFL6057K/12, 47PFL6057T/12/60, 47PFL6067H/12/60, 47PFL6067K/12, 47PFL6067T/12/60, 47PFL6097H/12/60, 47PFL6097K/12, 47PFL6097T/12/60, 47PFL6687H/12/60, 47PFL6687K/12, 47PFL6687T/60, 47PFL6877H/12/60, 47PFL6877K/12, 47PFL6877T/12/60
55PFL6007H/12, 55PFL6007K/12, 55PFL6007T/12, 55PFL6097H/12, 55PFL6097K/12, 55PFL6097T/12
The appearance of MainBoard 310431365664 is shown in the figure below:310431365664
310431365664 can be used in TVs:
PHILIPS 32PFL6007T/12 (Panel LC320EUF FEP1 code 423), PHILIPS 32PFL6008T/60 (Panel LC320EUF (FE)(P1) code 423), PHILIPS 32PFL6087T/12 (Panel LC320EUF (FE)(P1)), PHILIPS 32PFL6087T/12 (Panel LC320EUF FE P1), PHILIPS 42PFL6007T/60 (Panel LC420EUF (FE)(P1)), PHILIPS 42PFL6057T/60 (Panel LC420EUF FC P1), PHILIPS 42PFL6097T/60 (Panel LC420EUF (FE)(P1) code 322 p/n: 932228895682), PHILIPS 42PFL6877T/60 (Panel LC420EUF (FE)(P1)), PHILIPS 47PFL6057T/60 (Panel LC470EUF FE P1 (LG/PH) B code 323 p/n: 932228896682), PHILIPS 47PFL6097T/60 (Panel LC470EUF (FE)(P1)), PHILIPS 47PFL6877T/60 (Panel LC470EUF FE P1), PHILIPS 55PFL6007T/12 (Panel C550EUF (FE)(P1)), PHILIPS 60PFL9607T/12 (Panel LK600D3LB63 (SRJ)), PHILIPS 42PFL6067T/12 (Panel LC420EUF (FE)(P1)), PHILIPS 47PFL6007K/12 (Panel LC470EUF (FE)(P1)).
The appearance of the power supply
Key Features of PHILIPS 32PFL6008T:
Installed matrix (LED-panel) LC320EUF (FE) (P1) code 423.
To power the backlight LEDs, a converter is used, combined with a power supply unit, controlled by the OZ9909TN PWM controller.
The necessary supply voltages for all nodes of the PHILIPS 32PFL6008T TV are generated by the PLDD-P109A power supply module or its analogs using L6599 (PWM Resonant), FSL106HR (Standby DIP-8) microcircuits.
MainBoard - the main board (motherboard) is a module 310431365664, using chips FUSION120, H5TQ2G83BFR, H26M21001ECR, TAS5731P1 and others.
The SUT-RE214AN tuner provides TV reception and channel tuning.
Additional technical information about the panel:
Brand: LG Display
Model: LC320EUF-FEP1
Type: a-Si TFT-LCD, Panel
Diagonal size: 31.5 inch
Resolution: 1920x1080, FHD
Display Mode: S-IPS, Normally Black, Transmissive
Active Area: 698.4x392.85 mm
Surface: Antiglare (Haze 1%), Hard coating (2H)
Brightness: 400 cd / m²
Contrast Ratio: 1600: 1
Display Colors: 16.7M / 1.06B (8-bit / 8-bit + Dithering), CIE1931 72%
Response Time: 5 (G to G); 8 (MPRT)
Frequency: 120Hz
Lamp Type: 14S6P WLED Without Driver
Signal Interface: LVDS (4 ch, 8/10-bit), 92 pins
Voltage: 12.0V