Technical description and composition of the SAMSUNG UE22H5000 TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: UE22H5000 UE22H5000AK
Panel: M215HTN01.1 // HT215F01-100
LED driver (backlight): with integrated PSU
PWM LED driver: BD93941FP
Power Supply (PSU): BN44-00692A
PWM Power: SSC1S311
MainBoard: BN41-02105A (BN94-07144K)
IC MainBoard: CPU: NT14L, SPI Flash: 25Q40, NAND: F59L1G81A
Tuner: BN40-00281A
Technical Specifications UE22H5000
SAMSUNG UE22H5000
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE22H5000 TV does not turn on. There are no signs of operability. The indicators on the front panel do not light or flash, the TV does not respond to the remote control and control buttons.
In some of these cases, the main switching power supply, the BN44-00692A module, is faulty. It is necessary to measure its secondary output voltages, and if they are absent, check the power switches and rectifier diodes in the converters for a short circuit.
In case of any breakdowns in the secondary circuits, the converter can operate in emergency short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse or the current sensor at the source of the key more often breaks.
Mos-Fet power switches used in switching power supplies sometimes fail due to a malfunction of any other elements that can put it out of operation in key mode or create an excess of the maximum permissible key parameters. These can be elements supplying the PWM controller, frequency-setting or damping circuits, or negative feedback elements in the stabilization circuit. PWM controllers SSC1S311, in the absence of visible damage or frank short-circuit between the terminals, are checked by replacing with new, or obviously working.
- There is no image, there is sound, it responds to the remote control. Or the image may appear for a second when turned on and immediately disappears.
In some of these cases, a malfunction is caused by a lack of display backlight. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It should be remembered that it is not possible to determine the break in the LED lines without disassembling the panels with a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required. Then it is necessary to open the panel and check each LED separately with a multimeter. If the capabilities of your multimeter do not allow you to open the LED in the forward direction or dual LEd are used, then the PN junction of the emergency zener diode can indirectly serve as a health indicator. In case of LED-a malfunction, the zener diode PN junction will either be cut off or broken into short-circuit.
- The TV does not turn on, the indicator signals standby or working mode, or blinks.
Repair or diagnostics of the BN41-02105A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Board repair and replacement of CPU chips: NT14L, SPI Flash: 25Q40, NAND: F59L1G81A are carried out with the necessary equipment, and the corresponding element base. Faults associated with the application of BGA processor soldering technologies can be localized by the heating method.
The malfunction of the tuner BN40-00281A is established after checking the software and all the supply voltages at its terminals. The data exchange of the tuner with the processor via the I2C bus can be controlled by an oscilloscope.
Attention! Users and owners of UE22H5000 TVs who do not have the appropriate qualifications, knowledge and experience are strongly discouraged from attempting self-repair in order to avoid negative consequences that could lead to complete non-repairability of the device.
SCHEMATICS --------> SAMSUNG Chassis: U8AB Model: UE22H5000AW, Chassis: U8AA Model: UE32H5000AW, UE40H5000AW, UE48H5000AW, UE50H5000AW SERVICE MANUAL
The appearance of the MainBoard BN41-02105A is shown in the figure below:BN41-02105A
BN41-02105A can be used in TVs:
SAMSUNG T24D310EX (Panel V236BJ1-LE2 REV.C5), SAMSUNG UE28H4000AK (Panel HH028AAGH-R1), SAMSUNG T28D310EX (Panel HH028AGH-R2), SAMSUNG UE22H5000 UE22H5000AK (Panel MG28HT28) UE28J4100AK UE28J4100A (Panel HH028AGH-R2 ST2751A02-1).
The appearance of the power supply
Main features of the SAMSUNG UE22H5000 device:
Installed matrix (LED panel) M215HTN01.1 or HT215F01-100.
To power the backlight LEDs, a converter is used, combined with a power supply unit, controlled by the BD93941FP PWM controller.
The formation of the necessary supply voltages for all nodes of the SAMSUNG UE22H5000 TV is carried out by the BN44-00692A power module, or its analogs using SSC1S311 microcircuits.
MainBoard - the main board (motherboard) is a BN41-02105A module, using CPU chips: NT14L, SPI Flash: 25Q40, NAND: F59L1G81A and others.
The tuner BN40-00281A provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: AUO
Model: M215HTN01.1
Type: a-Si TFT-LCD, Panel
Diagonal size: 21.5 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 476.64x268.11 mm
Surface: Antiglare, Hard coating (3H)
Brightness: 250 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (6-bit + Hi-FRC), CIE1931 72%
Response Time: 3.8 / 1.2 (Tr / Td)
Frequency: 60Hz
Lamp Type: 12S4P WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V