Technical description and composition of the SAMSUNG UE32H5020AK TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: UE32H5020AK
Panel: CY-GH032BGLV4V // CY-GH032BGLV4V
LED backlight: D4GE-320DC1-R2 (03/14/17)
T-CON: BN95-01893A LSF320HN04 (BN41-02111)
LED driver (backlight): integrated into PSU; 101V 450mA
PWM LED driver: 7014X
Power Supply (PSU): BN44-00697A
PWM Power: S3330 (FAN6755)
MOSFET Power: 60R580P
MainBoard: BN41-02098B BN94-08113F // BN94-07142E
IC MainBoard: SPI Flash: 25Q40CLSIP, RAM: K4B2G1646Q - BCKO, AUDIO: NTP7414, S24C256, AOZ3015PI
Tuner: BN40-00288A
Technical Specifications UE32H5020
SAMSUNG UE32H5020AK
General repair guidelines for TV LCD LED
Possible manifestations of defects
- SAMSUNG UE32H5020AK does not turn on at all. There is no reaction to the remote control or to the control buttons from the front panel. Indicator lights do not light or flash.
In the vast majority of such cases, a malfunction is detected in the BN44-00697A power supply module. It is necessary to measure its output voltages and, if they are absent, to check the short circuit probability in the converters power switches and rectifier diodes.
During thermal or avalanche breakdowns of semiconductors in the secondary circuits of any converter, as a rule, it can operate in emergency short circuit mode without output voltages, and during short circuit in the elements of the primary circuit, the main fuse and, less often, the current sensor at the source of the key most often breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. It can be supply, damper circuits, or elements of OOS (negative feedback) stabilization. The reason for the breakdown of the power key may be PWM IC_Power. It is checked only by replacement with a known good one.
- There is no image, there is sound, it responds to the remote control, the channels are switched. In some cases, the image appears when you turn on and immediately disappears.
Usually in such cases, a malfunction is detected in the backlight nodes of the LED panel. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
When trying to identify a break in the LED lines, it should be borne in mind that it is difficult to do this without disassembling the panel. For example, a current source is needed to open PN junctions connected in series.
- The TV does not turn on, does not respond to the remote control. The indicator blinks or signals standby mode.
Repair or diagnostics of the BN41-02098B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its SPI Flash chips: 25Q40CLSIP, RAM: K4B2G1646Q - BCKO, AUDIO: NTP7414, S24C256, AOZ3015PI and other possible faulty components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
In the absence of tuning to the channels of on-air or cable television, you should make sure that the software is correct, as well as in accordance with the ratings of the supply voltages at the terminals of the tuner BN40-00288A. It is also necessary to check the presence of pulses of data exchange between the tuner and the processor via the I2C bus using an oscilloscope.
Attention TV owners! Attempts to self-repair SAMSUNG UE32H5020AK are not recommended by the manufacturer and can lead to serious negative consequences!
The appearance of the MainBoard BN41-02098B is shown in the figure below:BN41-02098B
BN41-02098B can be used in TVs:
SAMSUNG UE32H4270AU UE32H4270 (Panel HH032AGH-R1), SAMSUNG LT24D310ES (Panel V236BJ1-LE2), SAMSUNG UE40H5000AK (Panel CY-GH040BGLV1V), SAMSUNG UE48H5270AU UE48H5270 (Panel CY-GH048BGLV1V), SAMSUNG UE32H4290AU UE32H4290 (Panel HH032AGH-R2), SAMSUNG UE40H5290AU UE40H5290 (Panel CY-GH040BGLV1V), SAMSUNG UE40J5000AU UE40J5000 (Panel CY-JJ040BGNV2V), SAMSUNG UE40H5020 UE40H5020AK (Panel CY-GH040BGSV1V), SAMSUNG UE40J5100AU (Panel CY-GH040BGSR1V), SAMSUNG T31D310EW (Panel CY-HH032AGSV1H), SAMSUNG UE48J5000AU (Panel CY-JJ048BGEV5V), SAMSUNG UE32H5020AK (Panel CY-GH032BGLV4V), SAMSUNG UE40J5120AU (Panel CY-GH040BGSV1V), SAMSUNG LT32E310EX T32E310EX (Panel CY-GJ032BGEV1V), SAMSUNG UE40H5270 UE40H5270AU (Panel CY-GH048BGLV1V), SAMSUNG UE32J5100AK UE32J5100 (Panel CY-GH032BGSV1V), SAMSUNG UE32H5000AK UE32H5000 (Panel CY-GH032BGLV1V), SAMSUNG UE48H5000 UE48H5000AK (Panel CY-GH048CSLV1V), SAMSUNG UE32J5120AK UE32J5120 (Panel CY-GH032BGSV1V).
The appearance of the power supply
Main features of the SAMSUNG UE32H5020AK device:
Installed matrix (LED-panel) CY-GH032BGLV4V or CY-GH032BGLV4V.
The matrix control uses the Timing Controller (T-CON) BN95-01893A.
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by a 7014X PWM controller.
The necessary supply voltages for all nodes of the SAMSUNG UE32H5020AK TV are generated by the BN44-00697A power supply module or its analogs using S3330 microcircuits (FAN6755) and power switches of the 60R580P type.
MainBoard - the main board (motherboard) is a BN41-02098B module using SPI Flash chips: 25Q40CLSIP, RAM: K4B2G1646Q - BCKO, AUDIO: NTP7414, S24C256, AOZ3015PI and others.
The tuner BN40-00288A provides the reception of television programs and tuning to channels.