Technical description and composition of the SAMSUNG UE32H6230 TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: UE32H6230 UE32H6230AK
Chassis / Version: GH032CSA-B1
Panel: T320HVF05.2
T-CON: T500HVN09.1 CTRL BD 50T26-C01
LED driver (backlight): integrated into PSU
PWM LED driver: PIC16F753, 7014X
MOSFET LED driver: MDD7N25, FDD6N25
Power Supply (PSU): BN44-00707A
PWM Power: SPC7011F, FA6A01
MOSFET Power: 10N60M2 (PFC), KF7N50
MainBoard: BN41-02156A
IC MainBoard: CPU: SEMS31; SPI Flash: 25Q40CL; EEPROM: S24C512; SOUND: NTP7414
Tuner: HTQ403IH286A BN40-00288A
Technical Specifications UE32H6230
SAMSUNG UE32H6230
General repair guidelines for TV LCD LED
Possible manifestations of defects
- The SAMSUNG UE32H6230 TV does not turn on and does not show any signs of turning on, it does not respond to the control buttons or the remote control.
In some of these cases, a fault is detected in the BN44-00707A power supply module. It is necessary to measure its output voltages and, if they are absent, check the power switches (10N60M2 (PFC), KF7N50) and rectifier diodes for the short circuit probability in the converters.
In the event of breakdowns in the secondary circuits of the converter, it can usually fail in short circuit mode, and in the event of a short circuit in the power elements of the primary circuit, the mains fuse or current sensor at the source of the key most often breaks.
The breakdown of power switches (MosFet) in pulsed sources is sometimes caused by malfunctions of other circuit elements, for example, in the circuits supplying the PWM controller, frequency-setting or damper ones, as well as in the circuits of Negative Feedback (OOS) stabilization. PWM controllers (PWM) SPC7011F, FA6A01, if they do not have visible damage to the chassis and open short circuit between the terminals, are usually checked by replacement.
- There is no image, but there is sound and reaction to commands from the remote control. Or the image appears immediately after turning on and disappears.
Failure in most such cases is detected in the nodes and backlight elements of the LED panel. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To check the LED strips, to open all the transitions of the LEDs, several tens of volts or more are needed, it is best to use a current source for such purposes. The breakage of several PN junctions connected in series cannot be detected with a multimeter or tester. In such cases, it is necessary to open the panel and check each LED. If your multimeter cannot open the LED transitions in forward bias, you can sometimes detect the presence of a PN junction of the protective zener diode by connecting the probes in the opposite direction. If the zener diode is broken or broken in short-circuit, then the LED is faulty and needs to be replaced.
- The indicator blinks or glows constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the BN41-02156A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). Complex repair of MB (SSB) is possible only in the conditions of a service center with the necessary equipment. Checking or replacing CPU elements: SEMS31; SPI Flash: 25Q40CL; EEPROM: S24C512; SOUND: NTP7414 requires the necessary training and professional skills to repair modules at the component level. Problems associated with the use of BGA soldering technologies can sometimes be diagnosed by warming up.
If a tuner HTQ403IH286A BN40-00288A is suspected of malfunction, first of all, it is necessary to verify the correctness of the software, as well as the presence of the necessary supply voltage levels and data exchange pulses with the processor via the I2C bus at the corresponding tuner pins.
Owners and users of the SAMSUNG UE32H6230 TV should remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!
The appearance of the MainBoard BN41-02156A is shown in the figure below:BN41-02156A
BN41-02156A can be used in TVs:
SAMSUNG UE40H6200 UE40H6200AK (Panel CY-GH040CSLV1V), SAMSUNG UE32H5500 UE32H5500AK (Panel GH032BGA-B2), SAMSUNG UE40H5500 UE40H5500AK (Panel CY-GH040BGLV2V), SAMSUNG UE32H6200AK (Panel CY-GH032CSLV1V), SAMSUNG UE40H6350 (Panel CY-GH040CSLV2V), SAMSUNG UE32H6410AU UE32H6410 (Panel CY-GH032CSLV4V), SAMSUNG UE40H6400AK UE40H6400 (Panel CY-SH040CSL V2H), SAMSUNG UE48H6200 UE48H6200AK (Panel CY-GH048CSLV1V), SAMSUNG UE48H6230AK UE48H6230 (Panel CY-GH048CSLV1V), SAMSUNG UE48H6400AK UE48H6400 (Panel CY-GH048CSLV2V), SAMSUNG UE48H6410AU UE48H6410 (Panel CY-GH048CSLV4V), SAMSUNG UE48H6240AK UE48H6240 (Panel CY-GH048CSLV1V), SAMSUNG UE32H4500AK UE32H4500 (Panel CY-HH032AGLV2V), SAMSUNG UE40H6410 UE40H6410AU (Panel CY-GH040CSLV4V), SAMSUNG UE40H6500 UE40H6500AT (Panel CY-GH040CSLV1V), SAMSUNG UE32H6230 UE32H6230AK (Panel T320HVF05.2), SAMSUNG UE32H4510 UE32H4510AK (Panel HH032AGH-R3 BN96-31086F), SAMSUNG UE32H6350 UE32H6350AK (Panel CY-GH032CSLV2V), SAMSUNG UE40H6230 UE40H6230AK (Panel CY-GH048CSLV1V).
The appearance of the power supply
Main features of the SAMSUNG UE32H6230 device:
Installed matrix (LED-panel) T320HVF05.2.
The matrix control uses the Timing Controller (T-CON) T500HVN09.1.
To power the backlight LEDs, a converter is used, combined with a power supply unit, controlled by a PIC16F753, 7014X PWM controller. As power elements of the LED driver, keys of the type MDD7N25, FDD6N25 are used.
The necessary supply voltages for all nodes of the SAMSUNG UE32H6230 television are generated by the power module BN44-00707A, or its analogs using microcircuits SPC7011F, FA6A01 and power switches of the type 10N60M2 (PFC), KF7N50.
MainBoard - the main board (motherboard) is a BN41-02156A module, using CPU chips: SEMS31; SPI Flash: 25Q40CL; EEPROM: S24C512; SOUND: NTP7414 and others.
The tuner HTQ403IH286A BN40-00288A provides the reception of television programs and tuning to channels.
