Technical description and composition of the SAMSUNG UE32J6300 TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: UE32J6300 UE32J6300AU
Chassis / Version: UD03
Panel: CY-GH032CSLV5V
T-CON: BN95-01307B (BN41-02110A)
LED driver (backlight): integrated into PSU
PWM LED driver: 7014X
MOSFET LED driver: AOD9N40
Power Supply (PSU): BN44-00701B (L32S1P_FDY)
PWM Power: SPC7011F (FA5695), 3S111
MOSFET Power: TK10A60W
MainBoard: BN41-02353B BN94-09093P
IC MainBoard: SDP1415, EMMC: THGBMBG5D1KBAIT, RAM: K4B4G16460-BCMA
Tuner: BN40-00318A (DNTS243H5A)
Control: IR: BN41-02151A, WIFI: BN59-01174D (WIDT30Q), REMOTE: BN59-01220D (RMCTPJ1AP2)
Technical Specifications UE32J6300AU
SAMSUNG UE32J6300
General repair guidelines for TV LCD LED
Possible manifestations of defects
- SAMSUNG UE32J6300 TV does not turn on at all. The control lights do not light or flash. The TV on the remote control and the control panel buttons do not respond.
Most likely in this case, the main switching power supply (IIP) BN44-00701B is faulty. It is necessary to measure the output voltages in its secondary circuits, and if they are completely absent, check the serviceability of the power switches (TK10A60W) and rectifier diodes for possible breakdown (short circuit).
In case of breakdowns of semiconductors in secondary circuits, the converter can usually work abnormally in the short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse often breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) SPC7011F (FA5695), 3S111, in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, but there is sound and reaction to commands from the remote control. Or the image appears immediately after turning on and disappears.
Failure in most such cases is detected in the nodes and backlight elements of the LED panel. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
It is impossible to detect a break in the LED line without disassembling the panel with a simple multimeter. The LEDs are connected in series and to open their transitions, a voltage of several tens of volts is required. Ideally, a current source is suitable for such purposes. You can open the panel and check each LED separately. Typically, Chinese multimeters light up a single 3-volt LED, if you connect the probes in the forward direction to it (red probe to the anode, black to the cathode). In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as a health indicator. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights up constantly or blinks.
Repair or diagnostics of the BN41-02353B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). Complex repair of MB (SSB) is possible only in the conditions of a service center with the necessary equipment. Verification or replacement of elements SDP1415, EMMC: THGBMBG5D1KBAIT, RAM: K4B4G16460-BCMA requires the necessary training and professional skills in repairing modules at the component level. Problems associated with the use of BGA soldering technologies can sometimes be diagnosed by warming up.
If you suspect a malfunction of the tuner BN40-00318A (DNTS243H5A), first of all, you need to verify the correctness of the software, as well as the presence of the necessary voltage levels and pulses of data exchange with the processor via the I2C bus at the corresponding terminals of the tuner.
Attention TV owners! Attempts to self-repair SAMSUNG UE32J6300 are not recommended by the manufacturer and can lead to serious negative consequences!
The appearance of the MainBoard BN41-02353B is shown in the figure below:BN41-02353B
BN41-02353B can be used in TVs:
SAMSUNG UE40J6390 (Panel CY-GH040CSLV1V), SAMSUNG UE40J5530AU UE40J5530 (Panel CY-GJ040BGSV5V), SAMSUNG UE40J5500AU (Panel CY-GJ040BGSV5V), SAMSUNG UE40J5550 UE40J5550AU (Panel CY-GJ040BGSV1V), SAMSUNG UE40J6330AU (Panel CY-GH040CSLVFV), SAMSUNG UE32J6300 UE32J6300AU (Panel CY-GH032CSLV5V), SAMSUNG UE48J6200AU (Panel CY-GH048CSLVAV), SAMSUNG UE48J5510AU (Panel CY-GJ048BGLV3V), SAMSUNG UE32J6500AU UE32J6500 (Panel CY-WJ032CGLV2V), SAMSUNG UE40J5520AU UE40J5520 (Panel CY-GJ040BGSV5V), SAMSUNG UE43J5500 UE43J5500AU (Panel T430HVF01.0), SAMSUNG UE40J6200AU UE40J6200 (Panel CY-GH040CSLV8V), SAMSUNG UE32J5550AU UE32J5550 (Panel CY-GJ032BGAB3V), SAMSUNG UE32J5500AU (Panel T320HVF05.5), SAMSUNG UE40J6590 UE40J6590AU (Panel CY-WJ040CGLV1V), SAMSUNG UE40J5510AU (Panel CY-GJ040BGSV3V).
Main features of the SAMSUNG UE32J6300 device:
Installed matrix (LED panel) CY-GH032CSLV5V.
The matrix control uses the Timing Controller (T-CON) BN95-01307B.
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by a 7014X PWM controller. As power elements of the LED driver, keys of the AOD9N40 type are used.
The necessary supply voltages for all nodes of the SAMSUNG UE32J6300 TV are generated by the BN44-00701B power module or its analogs using SPC7011F (FA5695), 3S111 microcircuits and TK10A60W power switches.
MainBoard - the main board (motherboard) is a BN41-02353B module, using microchips SDP1415, EMMC: THGBMBG5D1KBAIT, RAM: K4B4G16460-BCMA and others.
The tuner BN40-00318A (DNTS243H5A) provides the reception of television programs and tuning to channels.
