Technical description and composition of the SAMSUNG UE40EH5050W TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: UE40EH5050W UE40EH5050
Chassis / Version: U71A / HS02
Panel: CY-DE400BGSV1L
T-CON: CTRL BD CPWBX 5246TP
LED driver (backlight): integrated into PSU
PWM LED driver: SLC2012M
Power Supply (PSU): BN44-00496A PD40AVF_CSM PSLF760C04A
PWM Power: SSC2S110
MOSFET Power: STI13NM60N, AOD9N40
MainBoard: BN41-01795A BN94-05842N
IC MainBoard: WT61P805, K4B1G1646G-BCH9, s24cs0, s24cs5, LVC244A, DRV612, NTP-7412S
Tuner: BN40-00231A DTOD40FVL084A
Appearance
SAMSUNG UE40EH5050W
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE40EH5050W does not turn on, the indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
In such cases, the power source — the BN44-00496A module — is sometimes faulty. It is necessary to measure its output voltages, and in case of their absence, check the serviceability of power switches (STI13NM60N, AOD9N40) of converters and rectifier diodes for the presence of a possible short circuit.
It should be borne in mind that for any breakdown of semiconductors in the secondary circuits, the converter, as a rule, can operate normally in the emergency short circuit mode. There are no output voltages. And during short circuit in the power elements of the primary circuit, as a rule, the mains fuse breaks and less often the current sensor at the source of the key.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, elements supplying a PWM controller, frequency-setting, damper, and also elements of the Negative Stabilization Feedback. PWM microcircuits, such as SSC2S110, are usually checked by replacing with new ones, or obviously working.
- There is no image, there is sound, it responds to the remote control, the channels are switched. In some cases, the image appears when you turn on and immediately disappears.
The most likely in these cases is a malfunction of the LED backlight. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It should be remembered that it is not possible to determine the open circuit in the LED lines without disassembling the panels with a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required. Then it is necessary to open the panel and check each LED separately with a multimeter. If the capabilities of your multimeter do not allow you to open the LED in the forward direction or dual LEd are used, then the PN junction of the emergency zener diode can indirectly serve as a health indicator. In case of LED-a malfunction, the zener diode PN junction will either be cut off or broken into short-circuit.
- The TV does not turn on, the indicator signals standby or working mode, or blinks.
Repair or diagnostics of the BN41-01795A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). Often, the MB (SSB) card must be replaced in case of complex malfunctions that are difficult to detect. When trying to repair, you should check its elements - WT61P805, K4B1G1646G-BCH9, s24cs0, s24cs5, LVC244A, DRV612, NTP-7412S and replace the failed chips with new ones. Some malfunctions may be due to the use of BGA soldering technologies in modern Main Board. Typically, such defects are detected by local heating of the chip.
In the absence of tuning to the channels of on-air or cable television, you should make sure that the software is correct, as well as in accordance with the ratings of the supply voltage at the terminals of the tuner BN40-00231A DTOD40FVL084A. It is also necessary to check the presence of pulses of data exchange between the tuner and the processor via the I2C bus using an oscilloscope.
Owners and users of the SAMSUNG UE40EH5050W TV should remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!
SCHEMATIC MANUAL ------------> Samsung UE40EH5050W shassis U71A,U71B.
UE32EH5****, UE22ES5****, UE37EH5**** UE19ES4****, UE40EH5****, UE46EH5****, UE26EH4****, UE32EH4****
The appearance of the MainBoard BN41-01795A is shown in the figure below:BN41-01795A
BN41-01795A can be used in TVs:
SAMSUNG UE32EH4000 UE32EH4000W (Panel LTJ320AP03-L), SAMSUNG UE32EH5000W (Panel DE320BGM-C1), SAMSUNG UE26EH4000W (Panel T260XVN01.1), SAMSUNG UE32EH5007K UE32EH5007 (Panel LTJ320HN07-L), SAMSUNG UE32EH5047K UE32EH5047 (Panel DE320BGA-B1), SAMSUNG UE40EH5007K (Panel CY-DE400BGSV1L), SAMSUNG UE32EH5057K (Panel DE320BGA-B1), SAMSUNG UE40FH5007K (Panel CY-DF400BGLV1V), SAMSUNG UE40EH5047K (Panel LTJ400HM08-L), SAMSUNG UE40EH5057K UE40EH5057 (Panel CY-DE400BGSV1L), SAMSUNG UE40EH5050W UE40EH5050 (Panel CY-DE400BGSV1L), SAMSUNG UE40EH5000 UE40EH5000W (Panel LTJ400HM801-V), SAMSUNG UE32EH5000K UE32EH5000 (Panel LTJ320HN07-L), SAMSUNG UE32EH5000W UE32EH5000 (Panel DE320BGM-C1), SAMSUNG LE32E420E2W LE32E420 (Panel LTF320AP13), SAMSUNG UE32EH4030 UE32EH4030W (Panel DE320AGH-C2), SAMSUNG UE46EH5057K UE46EH5057 (Panel LTJ460HN05-L), SAMSUNG UE40EH5040 UE40EH5040W (Panel CY-DE400BGSV1L).
The appearance of the power supply
Main features of the SAMSUNG UE40EH5050W device:
Installed matrix (LED panel) CY-DE400BGSV1L.
The matrix control uses the Timing Controller (T-CON) CTRL.
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by the SLC2012M PWM controller.
The necessary supply voltages for all nodes of the SAMSUNG UE40EH5050W TV are generated by the BN44-00496A power module or its analogs using SSC2S110 microcircuits and power switches of the STI13NM60N, AOD9N40 type.
MainBoard - the main board (motherboard) is a BN41-01795A module, using WT61P805, K4B1G1646G-BCH9, s24cs0, s24cs5, LVC244A, DRV612, NTP-7412S and other chips.
The tuner BN40-00231A DTOD40FVL084A provides the reception of television programs and tuning to channels.