Technical description and composition of the SAMSUNG UE40K5572 TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: UE40K5572 UE40K5572SU
Panel: CY-KK040BGLV3V
T-CON: RUNTK 5538TP
LED driver (backlight): integrated into PSU
PWM LED driver: SLC7015R02
Power Supply (PSU): BN44-00871A L40E1_KDY
PWM Power: FA1A50N, FA6A21N
MOSFET Power: 60R580P
MainBoard: BN41-02534B BN94-11366D
IC MainBoard: CPU: SDP1415, SPI Flash 25Q41, EEPPOM: 24C512, eMMC: THGBMBG5
Tuner: BN40-00318B DNTS243H5A
Control: Wi-Fi: WCK720Q
Technical Specifications UE40K5572SU
SAMSUNG UE40K5572
General repair guidelines for TV LCD LED
Possible malfunctions
- SAMSUNG UE40K5572 TV does not turn on, does not respond to the remote control and control panel buttons, indicators do not light up and do not blink.
In some of these cases, a fault is detected in the BN44-00871A power module. It is necessary to measure its output voltages and, if they are absent, check the serviceability of power switches (60R580P) and rectifier diodes in the converters for possible breakdown.
In case of breakdowns of semiconductors in secondary circuits, the converter can usually work abnormally in short circuit mode, and during short circuit in the power elements of the primary circuit, the main fuse often breaks.
Mos-Fet power switches used in switching power supplies sometimes fail due to a malfunction of any other elements that can put it out of operation in key mode or create an excess of the maximum permissible key parameters. These can be elements supplying the PWM controller, frequency-setting or damping circuits, or negative feedback elements in the stabilization circuit. PWM controllers FA1A50N, FA6A21N, in the absence of visible damage or frank faults between the terminals, are checked by replacing them with new ones, or obviously working.
- There is no image, there is sound, there is a reaction to the remote control. Or immediately after turning on for a second, the image may appear and immediately disappear.
A malfunction is usually most likely in these cases at the backlight nodes of the display matrix. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It should be remembered that it is not possible to determine the break in the LED lines without disassembling the panels with a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required. Then it is necessary to open the panel and check each LED separately with a multimeter. If the capabilities of your multimeter do not allow you to open the LED in the forward direction or dual LEd are used, then the PN junction of the emergency zener diode can indirectly serve as a health indicator. In case of LED-a malfunction, the zener diode PN junction will either be cut off or broken into short-circuit.
- The TV does not turn on, the indicator signals standby or working mode, or blinks.
Repair or diagnostics of the BN41-02534B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). Complex repair of MB (SSB) is possible only in the conditions of a service center with the necessary equipment. Checking or replacing CPU elements: SDP1415, SPI Flash 25Q41, EEPPOM: 24C512, eMMC: THGBMBG5 requires the necessary training and professional skills to repair modules at the component level. Problems associated with the use of BGA soldering technologies can sometimes be diagnosed by warming up.
Before replacing the BN40-00318B DNTS243H5A tuner, if there is no tuning for the channels, first check the software and the supply voltage at its terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus
Attention TV owners! Attempts to self-repair SAMSUNG UE40K5572 are not recommended by the manufacturer and can lead to serious negative consequences!
The appearance of the MainBoard BN41-02534B is shown in the figure below:BN41-02534B
BN41-02534B can be used in TVs:
SAMSUNG UE40K5500 (Panel CY-KK040BGLV1V), SAMSUNG UE32K5500 UE32K5500AW (Panel CY-KK032BGAV1V), SAMSUNG UE49K5500 UE49K5500BU (Panel CY-KK049BGLV1V).
The appearance of the power supply
Main features of the SAMSUNG UE40K5572 device:
Installed matrix (LED-panel) CY-KK040BGLV3V.
The matrix control uses the Timing Controller (T-CON) RUNTK.
To power the backlight LEDs, a converter is used, combined with a power supply unit, controlled by the SLC7015R02 PWM controller.
The necessary supply voltages for all nodes of the SAMSUNG UE40K5572 TV are generated by the BN44-00871A power module or its analogs using FA1A50N, FA6A21N microcircuits and 60R580P type power switches.
MainBoard - the main board (motherboard) is a BN41-02534B module, using CPU chips: SDP1415, SPI Flash 25Q41, EEPPOM: 24C512, eMMC: THGBMBG5 and others.
The tuner BN40-00318B DNTS243H5A provides the reception of television programs and tuning to channels.