Technical description and composition of the SAMSUNG UE40KU6300U TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: UE40KU6300U
Chassis / Version: BN41-02528A
Panel: CY-WK040HGLV1V
LED backlight: LM41-00120R & LM41-00120S & BN41-02375A
LED driver (backlight): integrated into PSU; 201V 0.5-1A
Power Supply (PSU): BN44-00806A REV 1.2 L40S6_FDY
MOSFET Power: K8A50D
MainBoard: BN41-02528A BN94-10769A
IC MainBoard: SDP1531, 25Q40, 25Q80, 24C512, K4F8E304H, K4F2E3S4H
Tuner: BN40-00323A
Control: WIFI: WIDT30Q BN59-01174D
Technical Specifications UE40KU6300U
SAMSUNG UE40KU6300U
General repair guidelines for TV LCD LED
Possible manifestations of defects
- SAMSUNG UE40KU6300U TV does not turn on at all. There is no reaction to the remote control and control buttons from the front panel. Indicator lights do not light or flash.
In some of these cases, the main switching power supply, the BN44-00806A module, is faulty. Then it is necessary to measure its output voltages and, in case of their complete or partial absence, it is necessary to check the serviceability of power switches (K8A50D) and rectifier diodes of the converters for the presence of a possible short circuit.
In case of breakdowns in the secondary circuits, the converter, as a rule, can emergency work in the short circuit mode, and during short circuit in the power elements of the primary circuit, the main fuse usually breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. PWM circuits are usually checked by replacement with new ones, or known to be working.
- There is no image, there is sound, there is a reaction to the remote control. Or immediately after turning on for a second, the image may appear and immediately disappear.
Failure in most such cases is detected in the nodes and backlight elements of the LED panel. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
To detect a break in the LED lines without disassembling the panel, a current source is required. It is impossible to open transitions connected in series with a simple multimeter; voltage of several tens of volts is necessary.
- The TV does not turn on, the indicator signals standby or working mode, or blinks.
Repair or diagnostics of the BN41-02528A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Sophisticated MB board repair (SSB) is in some cases possible and practiced by repairmen. To do this, check and, if necessary, replace the elements SDP1531, 25Q40, 25Q80, 24C512, K4F8E304H, K4F2E3S4H. BGA chip malfunctions are usually easy to detect by warming up.
Before changing the tuner BN40-00323A, if it is not possible to tune to television channels, make sure that there are supply voltages that must be measured at the corresponding terminals of the tuner and check the software for correctness. The pulses of the data exchange of the tuner with the processor can be controlled by an oscilloscope
Attention! Users and owners of UE40KU6300U TVs who do not have the appropriate qualifications, knowledge and experience are strongly discouraged from attempting self-repair in order to avoid negative consequences that could lead to complete non-serviceability of the device.
The appearance of the MainBoard BN41-02528A is shown in the figure below:
BN41-02528A
BN41-02528A can be used in TVs:
SAMSUNG UE43KU6650U (Panel CY-VK043HGAV5V), SAMSUNG UE43KU6000W UE43KU6000 (Panel CY-GK043HGEV1H), SAMSUNG UE55KU6400 UE55KU6400U (Panel CY-KK055HQLV4H), SAMSUNG UE49KU6670 UE49KU6670U (Panel CY-VK049HGLV4V), SAMSUNG UE40KU6000U (Panel LSF400FN05-L03 CY-GK040HGLV4V), SAMSUNG UE40KU6300U (Panel CY-WK040HGLV1V), SAMSUNG UE43KU6500U (Panel CY-VK043HGAV4V T430QVR01.0), SAMSUNG UE40KU6402U (Panel CY-KK040HGNV4H).
The appearance of the power supply
Main features of the SAMSUNG UE40KU6300U device:
Installed matrix (LED-panel) CY-WK040HGLV1V.
To power the backlight LEDs, a converter is used, combined with a power supply.
The formation of the necessary supply voltages for all nodes of the SAMSUNG UE40KU6300U TV is carried out by the BN44-00806A power module, or its analogues using power switches of the K8A50D type.
MainBoard - the main board (motherboard) is a BN41-02528A module, using microchips SDP1531, 25Q40, 25Q80, 24C512, K4F8E304H, K4F2E3S4H and others.
The tuner BN40-00323A provides the reception of television programs and tuning to channels.