Technical description and composition of the SAMSUNG UE43N5540AU TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: UE43N5540AU
Chassis / Version: AA01
Panel: CY-NN043BGAV1V
LED backlight: BN61-15482A
T-CON: 43T01-C04
LED driver (backlight): integrated into PSU
Power Supply (PSU): BN44-00956A
MainBoard: BN41-02575B BN94-13052A
IC MainBoard: CPU: SDP1604
Tuner: BN40-00331B
Control: BN59-01174D
Technical Specifications UE43N5540AU
SAMSUNG UE43N5540AU
General repair guidelines for TV LCD LED
Possible manifestations of defects
- The SAMSUNG UE43N5540AU TV does not turn on and does not show any signs of turning on, it does not respond to the control buttons or the remote control.
In such cases, the fault should be sought first in the BN44-00956A power supply module. It is necessary to measure its secondary output voltages, and if they are absent, check the power switches and rectifier diodes in the converters for a short circuit.
In case of breakdowns in the secondary circuits, the converter, as a rule, can emergency work in the short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse usually breaks.
The breakdown of power switches (MosFet) in pulsed sources is sometimes caused by malfunctions of other circuit elements, for example, in the circuits supplying the PWM controller, frequency-setting or damper ones, as well as in the circuits of Negative Feedback (OOS) stabilization. PWM controllers (PWM), if they do not have visible damage to the chassis and open short circuit between the terminals, are usually checked by replacement.
- There is no image, but there is sound and reaction to commands from the remote control. Or the image appears immediately after turning on and disappears.
The most likely in these cases is a malfunction of the LED backlight. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To check the LED strips, to open all the transitions of the LEDs, several tens of volts or more are needed, it is best to use a current source for such purposes. The breakage of several PN junctions connected in series cannot be detected with a multimeter or tester. In such cases, it is necessary to open the panel and check each LED. If your multimeter cannot open the LED transitions in forward bias, you can sometimes detect the presence of a PN junction of the protective zener diode by connecting the probes in the opposite direction. If the zener diode is broken or broken in short-circuit, then the LED is faulty and needs to be replaced.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the BN41-02575B motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software).
If there is no reception of television channels, but the TV is working properly from external devices, first of all, check the voltage of the tuner BN40-00331B and update the software. The pulses from the I2C bus must be controlled with an oscilloscope.
We recommend the owners of the UE43N5540AU TV for repair only to qualified specialists with the necessary work experience! Attempts to repair it yourself without the appropriate knowledge and skills can lead to irreversible negative consequences!
The appearance of the MainBoard BN41-02575B is shown in the figure below:BN41-02575B
The appearance of the power supply
Main features of the SAMSUNG UE43N5540AU device:
Installed matrix (LED-panel) CY-NN043BGAV1V.
The matrix control uses the Timing Controller (T-CON) 43T01-C04.
To power the backlight LEDs, a converter is used, combined with a power supply.
The formation of the necessary supply voltages for all nodes of the SAMSUNG UE43N5540AU TV is carried out by the BN44-00956A power module, or its analogues.
MainBoard - the main board (motherboard) is a BN41-02575B module, using CPU chips: SDP1604 and others.
The tuner BN40-00331B provides the reception of television programs and tuning to channels.