Technical description and composition of the SAMSUNG UE46B6000VW TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: UE46B6000VW UE46B6000
Chassis / Version: N74A
Panel: LTF460HF08
T-CON: BN59-00936A
LED driver (backlight): integrated into PSU
Power Supply (PSU): BN44-00269A (B) PSLF171B01A PD4612F1
PWM Power: MC33067P
MainBoard: BN41-01190B BN94-02662P
IC MainBoard: WM8593SEFT, RTL8100CSL, K4T1G164QE-HCE7
Tuner: BN40-00145B TDHG6-K13A
Control: BN59-00936A
Technical Specifications UE46B6000VW
SAMSUNG UE46B6000VW
General repair guidelines for TV LCD LED
Possible manifestations of defects
- SAMSUNG UE46B6000VW does not turn on at all and does not show any signs of operability. Does not blink indicators and does not respond to control buttons.
In the vast majority of such cases, a malfunction is detected in the BN44-00269A power supply module. It is then necessary to measure its output voltages and, if they are absent, you should check the power switches and rectifier diodes of the converters for the probability of a short circuit.
During thermal and avalanche breakdowns of semiconductors in secondary circuits, the converter can usually work normally in emergency short circuit mode. There are no output voltages. And during short circuit in the power elements of the primary circuit, as a rule, the mains fuse breaks and less often the current sensor at the source of the key.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, power supply, frequency-setting, damper ... as well as elements of the Negative Stabilization Feedback. The PWM chip MC33067P can also cause a malfunction of the power switch of the converter and is checked by replacement.
- There is no image, but there is sound and reaction to the remote control. Or for a second, the image may appear immediately after switching on.
Often in such cases, there is no LED backlight. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
To check the health in the LED circuit, it is better to use a current source with a maximum voltage of 200V. We do not recommend using any voltage sources for this purpose. You can test each LED individually with a simple Chinese multimeter (powered by 9 volts) in the P-N-junction test mode. If you connect the red probe of the multimeter to the anode of the LED, and the black to its cathode, then the 3-volt LED will light up slightly, and in the opposite direction you can detect the transition of the emergency zener diode. A zener diode PN junction indirectly indicates a LED-a
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights up constantly or blinks.
Repair or diagnostics of the BN41-01190B motherboard should begin by checking the stabilizers and power converters needed to power the microcircuit and matrix. If necessary, you should update or replace the software (software). In some cases, to repair the MB board (SSB), it may be necessary to replace the chips - WM8593SEFT, RTL8100CSL, K4T1G164QE-HCE7 with new or obviously good ones. In cases where BGA technologies are used, defects are usually localized by the heating method.
In the absence of tuning to the channels of on-air or cable television, you should make sure that the software is correct, as well as in accordance with the ratings of the supply voltage at the terminals of the tuner BN40-00145B TDHG6-K13A. It is also necessary to check, using an oscilloscope, the presence of pulses of data exchange between the tuner and the processor via the I2C bus.
Attention TV owners! Attempts to self-repair SAMSUNG UE46B6000VW are not recommended by the manufacturer and can lead to serious negative consequences!
The appearance of the MainBoard BN41-01190B is shown in the figure below:BN41-01190B
BN41-01190B can be used in TVs:
SAMSUNG UE40B6000VW UE40B6000 (Panel LTF400HF08), SAMSUNG UE46B7000WW UE46B7000 (Panel LTF460HF08), SAMSUNG UE46B6000VW UE46B6000 (Panel LTF460HF08), SAMSUNG UE46B7020 UE46B7020WW (Panel LTF460HF08).
The appearance of the power supply
Main features of the SAMSUNG UE46B6000VW device:
Installed matrix (LED-panel) LTF460HF08.
The matrix control uses the Timing Controller (T-CON) BN59-00936A.
To power the backlight LEDs, a converter is used, combined with a power supply.
The formation of the necessary supply voltages for all nodes of the SAMSUNG UE46B6000VW TV is carried out by the BN44-00269A power module, or its analogs using MC33067P microcircuits.
MainBoard - the main board (motherboard) is a module BN41-01190B, using microcircuits WM8593SEFT, RTL8100CSL, K4T1G164QE-HCE7 and others.
The tuner BN40-00145B TDHG6-K13A provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: SAMSUNG
Model: LTF460HF08
Type: a-Si TFT-LCD, Panel
Diagonal size: 46 inch
Resolution: 1920x1080, FHD
Display Mode: SPVA, Normally Black, Transmissive
Active Area: 1018.08x572.67 mm
Frequency: 60Hz
Lamp Type: CCFL
Signal Interface: LVDS (2 ch, 8-bit)