Technical description and composition of the SAMSUNG UE46EH5057K TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: UE46EH5057K UE46EH5057
Chassis / Version: U71A / TS01
Panel: LTJ460HN05-L
LED backlight: BN96-21487A (BN41-01825A), 46-3535LED-72EA-R / L D1GE-460SCB-R3 (12.04,12)
T-CON: LSJ460HN03-S BN41-01797A
LED driver (backlight): integrated into PSU
PWM LED driver: SEM5025
MOSFET LED driver: MDD5N40RH
Power Supply (PSU): BN44-00497A PD46AVF_CSM PSLF860C04A
PWM Power: SPC7011F (PFC), D2011K (Stby), FSFR1700
MOSFET Power: MDF11N60TH
MainBoard: BN41-01795A BN94-06144E
IC MainBoard: WT61P805, 25Q40, K4B1G1646G-BCH9, s24cs0, s24cs5, LVC244A, DRV612, NTP-7412S
Tuner: BN40-00231A DT0D40FVL084AA
Control: IR: BN96-22413C (BN41-01840B)
Appearance
SAMSUNG UE46EH5057K
General repair guidelines for TV LCD LED
Possible manifestations of defects
- SAMSUNG UE46EH5057K does not turn on and does not show any signs of performance at all. Does not blink indicators and does not respond to control buttons.
In such cases, the fault should be sought first in the BN44-00497A power supply module. Then it is necessary to measure its output voltages and, in case of their complete or partial absence, it is necessary to check the serviceability of power switches (MDF11N60TH) and rectifier diodes of converters for possible short circuit.
In case of breakdowns of semiconductors in the secondary circuits of any converter, as a rule, it can operate in emergency short-circuit mode without output voltages, and during short circuit in the elements of the primary circuit, the mains fuse and, less often, the current sensor at the source of the key are most often cut off.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) SPC7011F (PFC), D2011K (Stby), FSFR1700, in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, there is sound, there is a reaction to the remote control. Or immediately after turning on for a second, the image may appear and immediately disappear.
In such cases, the most likely malfunction of the LED backlight elements. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It is impossible to detect a break in the LED line without disassembling the panel with a simple multimeter. The LEDs are connected in series and to open their transitions, a voltage of several tens of volts is required. Ideally, a current source is suitable for such purposes. You can open the panel and check each LED separately. Usually, Chinese multimeters light up a single 3-volt LED, if you connect the probes in the forward direction to it (red probe to the anode, black to the cathode). In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as a health indicator. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The indicator on the front panel blinks, the TV does not turn on in operating mode, it does not respond to the remote control.
Repair or diagnostics of the BN41-01795A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). Often, the MB (SSB) card must be replaced in case of complex malfunctions that are difficult to detect. When trying to repair, you should check its elements - WT61P805, 25Q40, K4B1G1646G-BCH9, s24cs0, s24cs5, LVC244A, DRV612, NTP-7412S and replace the failed chips with new ones. Some malfunctions may be due to the use of BGA soldering technologies in modern Main Board. Typically, such defects are detected by local heating of the chip.
If the TV works normally from external devices, but does not tune into television channels, the tuner BN40-00231A DT0D40FVL084AA may be malfunctioning. In such cases, first of all, you should make sure that there are supply voltages at its corresponding terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus. Sometimes the cause of the inoperability of the tuner may be a software failure.
We recommend the owners of the UE46EH5057K TV for repair only to qualified specialists with the necessary work experience! Attempts to repair it yourself without the appropriate knowledge and skills can lead to irreversible negative consequences!
SCHEMATIC MANUAL ------------------> Samsung UE46EH5057K shassis U71A,U71B.
UE32EH5****, UE22ES5****, UE37EH5**** UE19ES4****, UE40EH5****, UE46EH5****, UE26EH4****, UE32EH4****
PSU SCHEMATIC Samsung ---------------------> PD46GO_BSM BN44-00473A Power supply
The appearance of the MainBoard BN41-01795A is shown in the figure below:BN41-01795A
BN41-01795A can be used in TVs:
SAMSUNG UE32EH4000 UE32EH4000W (Panel LTJ320AP03-L), SAMSUNG UE32EH5000W (Panel DE320BGM-C1), SAMSUNG UE26EH4000W (Panel T260XVN01.1), SAMSUNG UE32EH5007K UE32EH5007 (Panel LTJ320HN07-L), SAMSUNG UE32EH5047K UE32EH5047 (Panel DE320BGA-B1), SAMSUNG UE40EH5007K (Panel CY-DE400BGSV1L), SAMSUNG UE32EH5057K (Panel DE320BGA-B1), SAMSUNG UE40FH5007K (Panel CY-DF400BGLV1V), SAMSUNG UE40EH5047K (Panel LTJ400HM08-L), SAMSUNG UE40EH5057K UE40EH5057 (Panel CY-DE400BGSV1L), SAMSUNG UE40EH5050W UE40EH5050 (Panel CY-DE400BGSV1L), SAMSUNG UE40EH5000 UE40EH5000W (Panel LTJ400HM801-V), SAMSUNG UE32EH5000K UE32EH5000 (Panel LTJ320HN07-L), SAMSUNG UE32EH5000W UE32EH5000 (Panel DE320BGM-C1), SAMSUNG LE32E420E2W LE32E420 (Panel LTF320AP13), SAMSUNG UE32EH4030 UE32EH4030W (Panel DE320AGH-C2), SAMSUNG UE46EH5057K UE46EH5057 (Panel LTJ460HN05-L), SAMSUNG UE40EH5040 UE40EH5040W (Panel CY-DE400BGSV1L).
The appearance of the power supply
Main features of the SAMSUNG UE46EH5057K device:
Installed matrix (LED-panel) LTJ460HN05-L.
The matrix control uses the Timing Controller (T-CON) LSJ460HN03-S.
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by the SEM5025 PWM controller. As the power elements of the LED driver, keys of the MDD5N40RH type are used.
The necessary supply voltages for all nodes of the SAMSUNG UE46EH5057K TV are generated by the BN44-00497A power supply module or its analogs using microchips SPC7011F (PFC), D2011K (Stby), FSFR1700 and power switches of the MDF11N60TH type.
MainBoard - the main board (motherboard) is a BN41-01795A module, using microchips WT61P805, 25Q40, K4B1G1646G-BCH9, s24cs0, s24cs5, LVC244A, DRV612, NTP-7412S and others.
The tuner BN40-00231A DT0D40FVL084AA provides the reception of television programs and tuning to channels.