Technical description and composition of the SAMSUNG UE46ES6540 TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: UE46ES6540 UE46ES6540U
Chassis / Version: Ver: TE02
Panel: LTJ460HW06-L
LED backlight: 7032LED
T-CON: LSJ460HW05-S BN41-01789a
LED driver (backlight): integrated into PSU
Power Supply (PSU): BN44-00520C PD46B1QE_CDY
PWM Power: UCC25600, SPC7011F (PFC = FA5695N), STR2A151D (Standby)
MainBoard: BN41-01807A - BN94-05898E
IC MainBoard: CPU: WT61P805 (Standby); NAND Flash: KLM2G1HE3F-B001; DRAM: K4B2G1646C-HCK0; SOUND: NTP7412S
Tuner: BN40-00236A
Control: Bluetooth: BN96-21431C, Wi-Fi: BN59-01148B
Technical Specifications UE46ES6540
SAMSUNG UE46ES6540
General repair guidelines for TV LCD LED
Sometimes the SAMSUNG UE46ES6540 TV just does not turn on. No control lights on the front panel are lit or blinking, the TV does not respond to the remote control and does not make any sounds or any signs of life when turned on. The most likely cause of the malfunction is the failure of the BN44-00520C PD46B1QE_CDY common power module. If it is working properly, you must check the standby batteries on the Main Board. It is advisable to start the troubleshooting of the power supply module by checking the state of the electrolytic capacitors of the rectifier filters and the mains fuse. Defective capacitors should be replaced. If the mains fuse is broken, it is necessary to check first of all the power semiconductor elements - rectifier diodes and transistors, which are often found in such a state of breakdown.
As a rule, the keys in switching power supplies (SMPS) are reliable enough and rarely fail for no reason to be looked for by checking other components of the circuit - electrolytic capacitors, resistors and semiconductor elements of the primary circuit. The PWM chip is checked by replacing it with a known good one.
Sometimes the SAMSUNG UE46ES6540 TV does not have an image, but there is sound, or the image appears and immediately disappears. In this case, there is a possibility of a malfunction of the LED driver - power converter for the backlight LEDs of the LTJ460HW06-L panel, or an open circuit in the LED circuit is possible. In such cases, first of all, it is necessary to verify the operability of the electrolytic capacitors of the filter by supplying the backlight unit.
In most cases of lack of backlight, it becomes necessary to disassemble the panel in order to check the LEDs, connectors, loops and all contact connections. If one or several LEDs does not work in one line, therefore, they are broken and should be replaced.
When diagnosing, it is necessary to take into account that it is impossible to check the open in the chain of LED lines without disassembling the panels using a tester or multimeter. To open all PN junctions connected in series, a voltage of the order of several tens of volts is required, and ideally, a current source. By opening the panel, each LED can be checked separately. Usually, Chinese multimeters light up a single 3-volt LED, if you connect probes in the forward direction to it. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as a health indicator. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
If the motherboard BN41-01807A - BN94-05898E is faulty, first of all it is necessary to check all the linear stabilizers and power converters of its chips, and also, if necessary, update the software (software). Sometimes you can check the health of MB only by replacement.
If it is not possible to replace the MB (SSB) card, you need to check the health of its elements - CPU: WT61P805 (Standby); NAND Flash: KLM2G1HE3F-B001; DRAM: K4B2G1646C-HCK0; SOUND: NTP7412S. Defective components should be replaced.
If the TV works normally from external devices, but does not tune into television channels, the tuner BN40-00236A may be malfunctioning. In such cases, first of all, you should make sure that there are supply voltages at its corresponding terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus. Sometimes the cause of the inoperability of the tuner may be a software failure.
We recommend the owners of the UE46ES6540 TV for repair only to qualified specialists with experience! Self-repair attempts without the appropriate knowledge and skills can lead to serious negative consequences!
Led: 46NNB 3D-7032LED-MCPCB-R V2GE 460GMB-R3(11,12,12); 46NNB 3D-7032LED-MCPCB-L V2GE 460SMA-R3(11,12,12).
SHEMATIC MANUAL --------------> SAMSUNG Chassis U78A/U79A Model: UE**ES61***, UE**ES63***, UE**ES65***, UE**ES67***, UE**ES68***.
The appearance of the MainBoard BN41-01807A is shown in the figure below:BN41-01807A
BN41-01807A can be used in TVs:
SAMSUNG UE40ES6550S (Panel LTJ400HV05-V), SAMSUNG UE46ES6547U UE46ES6547 (Panel LTJ460HW06-L), SAMSUNG UE40ES7207U (Panel LTJ400HL10-L), SAMSUNG UE46ES6540 UE46ES6540U (Panel LTJ460HW06-L), SAMSUNG UE40ES6750 MXRU (Panel LTJ400HV08-L), SAMSUNG UE32ES6727U UE32ES6727 (Panel LTJ320HW06-L), SAMSUNG UE40ES6757 UE40ES6757M (Panel LTJ400HV08-L), SAMSUNG UE32ES6550 UE32ES6550S (Panel LE320CSM-C1), SAMSUNG UE40ES6540S (Panel LTJ400HV07-L), SAMSUNG UE55ES6760 UE55ES6760SXZG (Panel LTJ550HW10-B), SAMSUNG UE32ES6540 UE32ES6540S (Panel LE320CSM-C1), SAMSUNG UE40ES6727 UE40ES6727U (Panel LTJ400HV08-L), SAMSUNG UE32ES6757M (Panel LE320CSM-C2).
PSU Advanced
The BN44-00520C power module is made using a Power Factor Correction (PFC) scheme to eliminate multiple AC harmonics introduced into the power supply by the device. The PFC node is a Step-Up Converter based on a PWM controller SPC7011F = FA5695N, which evenly distributes high-frequency impulses of the charging current of the electrolytic capacitor of the rectifier filter of the mains voltage over a period of 50 Hz. The current of its charge in this case will already be determined not by its reactance (usually 10-30 ohms for the network frequency), but by the elements of the converter. As a result, a change in the amplitude of the pulses (envelope) of the consumed current of the converter will repeat the shape and phase of the input sinusoidal voltage. The availability of the increased voltage (about + 380V) in the operating mode on the capacitor of the line filter indicates the serviceability of the PFC node.
The appearance of the power supply
Main features of the SAMSUNG UE46ES6540 device:
Installed matrix (LED-panel) LTJ460HW06-L.
The matrix control uses the Timing Controller (T-CON) LSJ460HW05-S.
To power the backlight LEDs, a converter is used, combined with a power supply.
The necessary supply voltages for all nodes of the SAMSUNG UE46ES6540 TV are generated by the power module BN44-00520C, or its analogs using microcircuits UCC25600, SPC7011F (PFC = FA5695N), STR2A151D (Standby).
MainBoard - the main board (motherboard) is a BN41-01807A module, using CPU chips: WT61P805 (Standby); NAND Flash: KLM2G1HE3F-B001; DRAM: K4B2G1646C-HCK0; SOUND: NTP7412S and others.
The tuner BN40-00236A provides the reception of television programs and tuning to channels.