Technical description and composition of the SAMSUNG UE46ES6720 TV, panel type and applicable modules. The composition of the modules.SAMSUNG LED
Model: UE46ES6720 UE46ES6720S
Chassis / Version: U78A / U79A
Panel: LTJ460HW07-L
LED backlight: EDGE LED 7030
T-CON: BN41-01789A LSJ460HW05-S
LED driver (backlight): integrated into PSU
PWM LED driver: SLC5012M
MOSFET LED driver: KF9N25D
Power Supply (PSU): BN44-00520C REV1.1
PWM Power: SPC7011F (PFC), SQD2011K (Stb), UCC25600
MOSFET Power: TK8A50D
MainBoard: BN41-01807A
IC MainBoard: WT61P805 (Standby), KLM2G1HE3F-B001, K4B2G1646C-HCK0, NTP7412S
Tuner: BN40-00236A
Technical Specifications UE46ES6720
SAMSUNG UE46ES6720
General repair guidelines for TV LCD LED
Possible manifestations of defects
- SAMSUNG UE46ES6720 TV does not turn on, does not respond to the remote control and control panel buttons, indicators do not light up and do not blink.
In such cases, the BN44-00520C power supply is usually faulty. It is necessary to measure the output voltages in its secondary circuits, and if they are completely absent, check the serviceability of the power switches (TK8A50D) and rectifier diodes for possible breakdown (short circuit).
In case of any breakdowns in the secondary circuits, the converter can operate in emergency short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse or the current sensor at the source of the key more often breaks.
The breakdown of power switches (MosFet) in pulsed sources is sometimes caused by malfunctions of other circuit elements, for example, in the circuits supplying the PWM controller, frequency-setting or damper ones, as well as in the circuits of Negative Feedback (OOS) stabilization. PWM controllers (PWM) SPC7011F (PFC), SQD2011K (Stb), UCC25600, if they do not have visible damage to the case and open fault between the terminals, are usually checked by replacement.
- There is no image, the screen is black, there is sound, with external illumination of the screen, you can sometimes see barely noticeable outlines of the image.
Usually in such cases there is no backlighting of the LED panel (matrix). The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
To detect a break in the LED lines without disassembling the panel, a current source is required. It is impossible to open transitions connected in series with a simple multimeter; voltage of several tens of volts is necessary.
- The TV does not turn on, does not respond to the remote control. The indicator blinks or signals standby mode.
Repair or diagnostics of the BN41-01807A motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, you should update or replace the software (software). Sophisticated MB board repair (SSB) is in some cases possible and practiced by repairmen. To do this, check and, if necessary, replace the elements WT61P805 (Standby), KLM2G1HE3F-B001, K4B2G1646C-HCK0, NTP7412S. BGA chip malfunctions are usually easy to detect by warming up.
Before changing the tuner BN40-00236A, if it is not possible to tune to television channels, make sure that there are supply voltages that must be measured at the corresponding terminals of the tuner and check the software for correctness. The pulses of the data exchange of the tuner with the processor can be controlled by an oscilloscope
Attention to users! Self-repair of a SAMSUNG UE46ES6720 TV without the appropriate qualifications and necessary experience can lead to its complete non-repairability!
SCHEMATIC MANUAL ---------------> SAMSUNG Chassis U78A/U79A Model: UE**ES61***, UE**ES63***, UE**ES65***, UE**ES67***, UE**ES68***.
SCHEMATIC OF PSU Power supply BN44-00520C.
BN41-01807A
BN41-01807A can be used in TVs:
SAMSUNG UE40ES6550S (Panel LTJ400HV05-V), SAMSUNG UE46ES6547U UE46ES6547 (Panel LTJ460HW06-L), SAMSUNG UE40ES7207U (Panel LTJ400HL10-L), SAMSUNG UE46ES6540 UE46ES6540U (Panel LTJ460HW06-L), SAMSUNG UE40ES6750 MXRU (Panel LTJ400HV08-L), SAMSUNG UE32ES6727U UE32ES6727 (Panel LTJ320HW06-L), SAMSUNG UE40ES6757 UE40ES6757M (Panel LTJ400HV08-L), SAMSUNG UE32ES6550 UE32ES6550S (Panel LE320CSM-C1), SAMSUNG UE40ES6540S (Panel LTJ400HV07-L), SAMSUNG UE55ES6760 UE55ES6760SXZG (Panel LTJ550HW10-B), SAMSUNG UE32ES6540 UE32ES6540S (Panel LE320CSM-C1), SAMSUNG UE40ES6727 UE40ES6727U (Panel LTJ400HV08-L), SAMSUNG UE32ES6757M (Panel LE320CSM-C2).
The appearance of the power supply
Main features of the SAMSUNG UE46ES6720 device:
Installed matrix (LED-panel) LTJ460HW07-L.
The matrix control uses the Timing Controller (T-CON) BN41-01789A.
To power the backlight LEDs, a converter is used, combined with the power supply, controlled by the SLC5012M PWM controller. As the power elements of the LED driver, keys of the KF9N25D type are used.
The necessary supply voltages for all nodes of the SAMSUNG UE46ES6720 TV are generated by the BN44-00520C power module or its analogs using SPC7011F (PFC), SQD2011K (Stb), UCC25600 microcircuits and TK8A50D type power switches.
MainBoard - the main board (motherboard) is a BN41-01807A module, using microchips WT61P805 (Standby), KLM2G1HE3F-B001, K4B2G1646C-HCK0, NTP7412S and others.
The tuner BN40-00236A provides the reception of television programs and tuning to channels