Technical description and composition of the LG 42LB653V TV, panel type and applicable modules. The composition of the modules.LG LED
Model: 42LB653V ZK
Chassis / Version: LD42B
Panel: LC420DUH (FG) (P1)
LED backlight: DIRECT 3.0 42INCH REV7 A-TYRE 131202 6916L-1709C, B-TYRE 6916L-1710C
LED driver (backlight): integrated into PSU; 208V 250mA
PWM LED driver: BD9486F
MOSFET LED driver: MDD3752, 4NF20
Power Supply (PSU): EAX65423701 (2.0) REV2.0 - LGP3942-14PL1
PWM Power: MAP8800 (PFC), FA6A01N (PWM resonant)
MOSFET Power: TK7P60W
MainBoard: EAX65384004 (1.5)
IC MainBoard: CPU: LG1311; DRAM: H5TQ4G63AFR-PBC; EEPROM: AT24C256C
Tuner: TDJM-G101D EBL61400501
Control: IR: Assy Ver 1.5; WIFI: Combo Module LGSBW41
Specifications 42LB653V
LG 42LB653V
General repair guidelines for TV LCD LED
If the TV does not turn on, no control lights are on or blinking, there are no sounds when you turn on, and there is not the slightest sign of operability - the most likely malfunction is in the power module. Diagnostics and repair of the common power supply should always begin with a check of the mains fuse and the condition of the electrolytic capacitors of the secondary rectifier filters. Defective and swollen capacitors should be replaced with new ones. If the fuse breaks, it is advisable to check for a breakdown, first of all, all power semiconductor elements of the converter and the diode bridge of the rectifier network, as well as a large electrolytic capacitor of the filter of the rectifier network.
As a rule, the keys in switching power supplies (SMPS) are reliable enough and rarely fail for no reason to be looked for by checking other components of the circuit - electrolytic capacitors, resistors and semiconductor elements of the primary circuit. The PWM chip is verified by replacing it with a known good one.
If the LG 42LB653V TV does not have an image, but there is sound, a malfunction in the backlight circuits of the LED panel LC420DUH (FG) (P1) is likely.
Often in the absence of backlighting, disassembling the panel is required. It is necessary to check the serviceability of the transitions of the LEDs, as well as the reliability of the contact connections in the rulers and connectors.
To check the health in the LED circuit, it is better to use a current source with a maximum voltage of 200V. We do not recommend using any voltage sources for this purpose. You can check each LED individually with a simple Chinese multimeter (powered by 9 volts) in the P-N-junction test mode. If you connect the red probe of the multimeter to the anode of the LED, and the black to its cathode, then the 3-volt LED will light up slightly, and in the opposite direction you can detect the transition of the emergency zener diode. A zener diode PN junction indirectly indicates a LED-a
The motherboard EAX65384004 (1.5) must be checked if there is no reaction to the remote control and function buttons, the standby indicator blinks or lights up continuously. In such cases, if the converters or power regulators of the microcircuit are working, a software update may be necessary.
In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its CPU chips: LG1311; DRAM: H5TQ4G63AFR-PBC; EEPROM: AT24C256C and other possible defective components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
Malfunction of the TDJM-G101D EBL61400501 tuner is established after checking the software and all supply voltages at its terminals. The data exchange of the tuner with the processor via the I2C bus can be controlled by an oscilloscope.
Attention! For users and owners of 42LB653V TVs who do not have the appropriate qualifications, knowledge and experience, we strongly recommend against attempting self-repair in order to avoid negative consequences that could lead to complete non-repairability of the device.
schematic diagram ------------> LG CHASSIS LD42B MODEL: 42LB65** 42LB65**-Z*.
User Manual ------------> WiFi LG Wi-Fi Module LGSBW41
Backlight Current Limit:
In televisions with power supplies LGP3942-14PL1 (EAX65423701), the backlight current sensor - the resistor block R811-R818 consists of four pairs of 4.3 Ohm each. You can reduce the backlight current by 25% by removing one pair of resistors.
More details on this page
The appearance of the MainBoard EAX65384004 is shown in the figure below:EAX65384004
EAX65384004 can be used in TVs:
LG 32LB650V ZE (Panel LC320DUH (FG)(P2)), LG 47LB650V ZE (Panel LC470DUH (FG) (P2)), LG 42LB650V (Panel LC420DUH (FG)(P2)), LG 42LB671V ZF (Panel LC420DUH (PG) (F1)), LG 47LB671V (Panel LC470DUH (PG)(F1)), LG 42LB653V ZK (Panel LC420DUH (FG)(P1)), LG 42LB720V (Panel LC420DUH (PG)(F1)), LG 42LB658V (Panel LC420DUH (FG)(P2)), LG 47LB677V (Panel LC470DUH (FG)(F1)), LG 42LB679V (Panel LC420DUH (PG)(F1)), LG 47LB653V (Panel LC470DUH (FG)(P1)), LG 32LB653V (Panel LC320DUH( FG)(P1)), LG 42LB690V (Panel LC420DUH (PG)(F1)), LG 55LB630V (Panel LC550DUH).
PSU Advanced
On the 42LB653V TV, the EAX65423701 power module is installed using the PFC (Power Factor Correction) scheme acting as an active filter to eliminate the higher harmonic components of the current consumption. The boost converter based on the MAP8800 PWM controller does not allow the electrolytic capacitor of the input rectifier filter to be connected directly to the network directly through open diodes, when the value of the charge current determines its reactance (about 15-30 ohms at a frequency of 50 Hz). As a result of the conversion, the charging current of the capacitor will be determined in such a way that the envelope of the high-frequency pulses of the input current will repeat the phase and shape of the sine wave of the input voltage. The health check of the PFC unit is carried out by measuring the DC voltage on the capacitor of the rectifier network. In operating mode, it should be around 380V, in standby approximately 300V.
The appearance of the power supply
Main features of the device LG 42LB653V:
Installed matrix (LED-panel) LC420DUH (FG) (P1).
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by the BD9486F PWM controller. As power elements of the LED driver, keys of the MDD3752, 4NF20 type are used.
The necessary supply voltages for all nodes of the LG 42LB653V TV are generated by the EAX65423701 power supply module or its analogs using MAP8800 (PFC), FA6A01N (PWM resonant) microcircuits and TK7P60W power switches.
MainBoard - the main board (motherboard) is an EAX65384004 module, using CPU chips: LG1311; DRAM: H5TQ4G63AFR-PBC; EEPROM: AT24C256C and others.
Tuner TDJM-G101D EBL61400501 provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: LG Display
Model: LC420DUH-FGP1
Type: a-Si TFT-LCD, Panel
Diagonal size: 42 inch
Resolution: 1920x1080, FHD
Display Mode: IPS, Normally Black, Transmissive
Active Area: 927.94x521.96 mm
Surface: Antiglare (Haze 1%), Hard coating (2H)
Brightness: 300 cd / m²
Contrast Ratio: 1200: 1
Display Colors: 16.7M (8-bit), CIE1931 68%
Response Time: 6/8 (Tr / Td)
Frequency: 120Hz
Lamp Type: WLED Without Driver
Signal Interface: EPI, 100 pins
Voltage: 12.0V