Technical description and composition of the LG 42LB675V TV, panel type and applicable modules. The composition of the modules.LG LED
Model: 42LB675V ZA
Chassis / Version: LD42B
Panel: LC420DUH (PG) (F1)
LED backlight: 6916L-1682A, 6916L-1683A, 6916L-1684A, 6916L-1685A
LED driver (backlight): integrated into PSU
PWM LED driver: iW7025-00
Power Supply (PSU): EAX65424001
PWM Power: MAP8800 (PFC), NCP1034DG, ICE3BR4765JZ (Standby DIP-7)
MOSFET Power: 13N60M2
MainBoard: EAX65384003 (1.2)
IC MainBoard: CPU: LG1311; DRAM: H5TQ4G63AFR-PBC; EEPROM: AT24C256C, EMMC: THGBMAG6A2JBAIR
Tuner: TDJM-G101D
Specifications 42LB675V
LG 42LB675V
General repair guidelines for TV LCD LED
Possible malfunctions
- LG 42LB675V does not turn on, the indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
In some of these cases, the main switching power supply, the EAX65424001 module, is faulty. It is necessary to measure its output voltages and, if they are absent, check the power switches (13N60M2) and rectifier diodes for the probability of short circuit in the converters.
In case of any breakdown of semiconductors in the secondary circuits, the converter can usually work normally in emergency short circuit mode. There are no output voltages. And with a short circuit in the power elements of the primary circuit, as a rule, the mains fuse breaks and less often the current sensor at the source of the key.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) MAP8800 (PFC), NCP1034DG, ICE3BR4765JZ (Standby DIP-7), in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, there is sound, it is responding to the remote control. Or immediately after turning on for a second, the image may appear and immediately disappear.
In some of these cases, the malfunction is caused by a lack of backlighting on the display. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It should be remembered that it is not possible to determine the open circuit in the LED lines without disassembling the panels with a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required. Then it is necessary to open the panel and check each LED separately with a multimeter. If the capabilities of your multimeter do not allow you to open the LED in the forward direction or dual LEd are used, then the PN junction of the emergency zener diode can indirectly serve as a health indicator. In case of LED-a failure, the zener diode PN junction will either be cut off or broken into short-circuit.
- The TV does not turn on, does not respond to the remote control. The indicator blinks or signals standby mode.
Repair or diagnostics of the EAX65384003 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its CPU chips: LG1311; DRAM: H5TQ4G63AFR-PBC; EEPROM: AT24C256C, EMMC: THGBMAG6A2JBAIR and other possible defective components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
Before changing the tuner TDJM-G101D, if it is not possible to tune to television channels, you should make sure that there are supply voltages that must be measured at the corresponding terminals of the tuner and check the software for correctness. The pulses of the data exchange of the tuner with the processor can be controlled by an oscilloscope
Once again, we remind TV users: you should not make attempts to repair it yourself without the appropriate knowledge, experience and the necessary qualifications! Entrust repair to professionals with sufficient experience in the field of repair of electronic equipment.
schematic diagram ------------> LG 42LB675V Chassis LD42B
The appearance of the MainBoard EAX65384003 is shown in the figure below:EAX65384003
EAX65384003 can be used in TVs:
LG 47LB650V ZE (Panel LC470DUH (FG) (P2)), LG 42LB631V ZL (Panel LC420DUH (FG) (A1)), LG 39LB650V (Panel T390HVJ01.2), LG 55LB673V ZB (Panel LC550DUH (PG)(F1)), LG 47LB677V (Panel LC470DUH (FG)(F1)), LG 42LB673V (Panel LC420DUH (PG)(F1)), LG 47LB673V (Panel LC470DUH (PG)(F1)), LG 32LB652V 32LB652V-ZA.BRUWLDU (Panel LC320DUH (FG)(P2)), LG 50LB653V (Panel LC500DUH (FG)(P1)), LG 42LB652V 42LB652V-ZA.BRUWLJU (Panel LC420DUH (FG)(P2)), LG 55LB720V 55LB720V-ZG.BRUWLJU (Panel LC550DUH (PG)(F1)).
The appearance of the power supply
Main features of the device LG 42LB675V:
Installed matrix (LED-panel) LC420DUH (PG) (F1).
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by the iW7025-00 PWM controller.
The necessary supply voltages for all nodes of the LG 42LB675V TV are generated by the EAX65424001 power module or its analogs using MAP8800 (PFC), NCP1034DG, ICE3BR4765JZ (Standby DIP-7) microcircuits and 13N60M2 type power switches.
MainBoard - the main board (motherboard) is an EAX65384003 module, using CPU chips: LG1311; DRAM: H5TQ4G63AFR-PBC; EEPROM: AT24C256C, EMMC: THGBMAG6A2JBAIR and others.
The TDJM-G101D tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: LG Display
Model: LC420DUH-PGF1
Type: a-Si TFT-LCD, Panel
Diagonal size: 42 inch
Resolution: 1920x1080, FHD
Display Mode: IPS, Normally Black, Transmissive
Active Area: 927.94x521.96 mm
Surface: Antiglare (Haze 1%), Hard coating (3H)
Brightness: 400 cd / m²
Contrast Ratio: 1400: 1
Display Colors: 1.06B (10-bit), CIE1931 72%
Response Time: 8/10 (Tr / Td)
Frequency: 120Hz
Lamp Type: WLED Without Driver
Signal Interface: EPI, 100 pins
Voltage: 12.0V