Technical description and composition of the LG 42LB680V TV, panel type and applicable modules. The composition of the modules.LG LED
Model: 42LB680V ZD
Chassis / Version: LD42B
Panel: LC420DUH (PG) (F1)
LED backlight: 42 V14 Slim DRT Rev0.6 1 R1-Type 6916L-1683A
LED driver (backlight): integrated into PSU
PWM LED driver: iW7025-00
Power Supply (PSU): EAX65424001 (2.3) REV2.0 LGP42-14LPB
PWM Power: NCP1034DG, MAP8800 (PFC), ICE3BR4765JZ
MOSFET Power: 13N60M2
MainBoard: EAX65384003 1.2 EBR78599402
IC MainBoard: CPU: LG1311; DRAM: H5TQ4G63AFR-PBC; EEPROM: AT24C256C, EMMC: THGBMAG6A2JBAIR
Tuner: TDJM-G101D
Specifications 42LB680V
LG 42LB680V
General repair guidelines for TV LCD LED
Possible manifestations of defects
- LG 42LB680V TV does not turn on. There are no signs of operability. The indicators on the front panel do not light or flash, the TV does not respond to the remote control and control buttons.
In such cases, the malfunction should be sought first in the EAX65424001 power supply module. Then it is necessary to measure its output voltages and, in case of their complete or partial absence, it is necessary to check the serviceability of power switches (13N60M2) and rectifier diodes of the converters for the presence of a possible short circuit.
In the event of breakdowns in the secondary circuits of the converter, it can usually fail in short circuit mode, and in the event of a short circuit in the power elements of the primary circuit, the mains fuse or current sensor at the source of the key most often breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. PWM microcircuits NCP1034DG, MAP8800 (PFC), ICE3BR4765JZ are usually checked by replacing with new ones, or obviously working.
- There is no image, there is sound, it responds to the remote control, the channels are switched. In some cases, the image appears when you turn on and immediately disappears.
In such cases, the most likely malfunction of the LED backlight elements. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It is impossible to check the line of series-connected LEDs without a special current source, and for this purpose it is not safe to use any voltage sources above 12V. Then it remains only to open the panel and check each LED separately. Usually, Chinese 9V-powered multimeters light up a single 3-volt LED, if you connect the probes in the forward direction, the red probe to the anode, and the black to the cathode. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of health. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The TV does not turn on, does not respond to the remote control. The indicator blinks or signals standby mode.
Repair or diagnostics of the EAX65384003 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its CPU chips: LG1311; DRAM: H5TQ4G63AFR-PBC; EEPROM: AT24C256C, EMMC: THGBMAG6A2JBAIR and other possible defective components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
Malfunction of the tuner TDJM-G101D is established after checking the software and all supply voltages at its terminals. The data exchange of the tuner with the processor via the I2C bus can be controlled by an oscilloscope.
Once again, remind users! Attempts to self-repair the LG 42LB680V TV without the appropriate qualifications and the necessary experience can lead to its complete non-repairability!
schematic diagram ------------> LG 42LB680V Chassis LD42B
The appearance of the MainBoard EAX65384003 is shown in the figure below:EAX65384003
EAX65384003 can be used in TVs:
LG 47LB650V ZE (Panel LC470DUH (FG) (P2)), LG 42LB631V ZL (Panel LC420DUH (FG) (A1)), LG 39LB650V (Panel T390HVJ01.2), LG 55LB673V ZB (Panel LC550DUH (PG)(F1)), LG 47LB677V (Panel LC470DUH (FG)(F1)), LG 42LB673V (Panel LC420DUH (PG)(F1)), LG 47LB673V (Panel LC470DUH (PG)(F1)), LG 32LB652V 32LB652V-ZA.BRUWLDU (Panel LC320DUH (FG)(P2)), LG 50LB653V (Panel LC500DUH (FG)(P1)), LG 42LB652V 42LB652V-ZA.BRUWLJU (Panel LC420DUH (FG)(P2)), LG 55LB720V 55LB720V-ZG.BRUWLJU (Panel LC550DUH (PG)(F1)).
The appearance of the power supply
Main features of the device LG 42LB680V:
Installed matrix (LED-panel) LC420DUH (PG) (F1).
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by the iW7025-00 PWM controller.
The necessary supply voltages for all nodes of the LG 42LB680V TV are generated by the EAX65424001 power module or its analogs using NCP1034DG, MAP8800 (PFC), ICE3BR4765JZ microcircuits and 13N60M2 type power switches.
MainBoard - the main board (motherboard) is an EAX65384003 module, using CPU chips: LG1311; DRAM: H5TQ4G63AFR-PBC; EEPROM: AT24C256C, EMMC: THGBMAG6A2JBAIR and others.
The TDJM-G101D tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: LG Display
Model: LC420DUH-PGF1
Type: a-Si TFT-LCD, Panel
Diagonal size: 42 inch
Resolution: 1920x1080, FHD
Display Mode: IPS, Normally Black, Transmissive
Active Area: 927.94x521.96 mm
Surface: Antiglare (Haze 1%), Hard coating (3H)
Brightness: 400 cd / m²
Contrast Ratio: 1400: 1
Display Colors: 1.06B (10-bit), CIE1931 72%
Response Time: 8/10 (Tr / Td)
Frequency: 120Hz
Lamp Type: WLED Without Driver
Signal Interface: EPI, 100 pins
Voltage: 12.0V