Technical description and composition of the LG 42LM620S TV, panel type and applicable modules. The composition of the modules.LG LED
Model: 42LM620S
Chassis / Version: LD22E
Panel: LC420EUE (SE) (F1)
LED backlight: 6920L-0001C AGS416 CF 42 V12 Edge REV1.1 1
T-CON: 6870C-0401B 32/37/42/47/55 FHD TM120 Ver0.2
LED driver (backlight): integrated into PSU
PWM LED driver: R5F100BCAFP, AAT2430AISX
MOSFET LED driver: PHT4NQ10LT
Power Supply (PSU): EAX64427101 (1.4) LGP4247L-12LPB
PWM Power: FAN7930BG (PFC), L6599AD (PWM), STR-A6059 (Stb)
MOSFET Power: STF13NM60N, STF10NM60N
MainBoard: EAX64307906 (1.0) EBT62049202
IC MainBoard: LCE2112, H5TQ2G63DFR, KLM2G1HE3F, MICOM R5F100GEA, 24C16
Tuner: TDSN-G351D
Specifications 42LM620S
LG 42LM620S
General repair guidelines for TV LCD LED
Possible manifestations of defects
- LG 42LM620S TV does not turn on at all. There is no reaction to the remote control and control buttons from the front panel. Indicator lights do not light or flash.
In such cases, the malfunction should be sought first in the EAX64427101 power supply module. Then it is necessary to measure its output voltages and, in case of their complete or partial absence, it is necessary to check the serviceability of power switches (STF13NM60N, STF10NM60N) and rectifier diodes of converters for possible short circuit.
In case of breakdowns of semiconductors in the secondary circuits, the converter can usually work abnormally in the short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse often breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. PWM chips FAN7930BG (PFC), L6599AD (PWM), STR-A6059 (Stb) are usually checked by replacing with new, or obviously working.
- There is no image, there is sound, it responds to the remote control, the channels are switched. In some cases, the image appears when you turn on and immediately disappears.
The most likely in these cases is a malfunction of the LED backlight. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
To check the health in the LED circuit, it is better to use a current source with a maximum voltage of 200V. We do not recommend using any voltage sources for this purpose. You can check each LED individually with a simple Chinese multimeter (powered by 9 volts) in the P-N-junction test mode. If you connect the red probe of the multimeter to the anode of the LED, and the black to its cathode, then the 3-volt LED will light up slightly, and in the opposite direction you can detect the transition of the emergency zener diode. A zener diode PN junction indirectly indicates a LED-a
- The TV does not turn on, does not respond to the remote control. The indicator blinks or signals standby mode.
Repair or diagnostics of the EAX64307906 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its chips LCE2112, H5TQ2G63DFR, KLM2G1HE3F, MICOM R5F100GEA, 24C16 and other possible faulty components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
If there is no reception of television channels, but the TV is working properly from external devices, first of all it is necessary to check the voltage of the TDSN-G351D tuner and update the software. The pulses from the I2C bus must be controlled with an oscilloscope.
Attention! For users and owners of 42LM620S TVs who do not have the appropriate qualifications, knowledge and experience, we strongly recommend against attempting self-repair in order to avoid negative consequences that could lead to complete non-repairability of the device.
SCHEMATIC DIAGRAM ---------> LG 42LM620S Chassis LD22E.
PSU SCHEMATIC DIAGRAM ---------> LG EAX64427101 LGP4247L-12LPB
To reduce the backlight current in LED drivers with the AAT2430AISX controller, increase the resistance of the resistor from terminal 50 (ISET) to the housing, for example, from 3 KOhm to 4.7 KOhm. Currents will proportionally decrease in each of the 16 channels. With a parallel connection of channels, currents are summed.
The appearance of the MainBoard EAX64307906 is shown in the figure below:EAX64307906
EAX64307906 can be used in TVs:
LG 32LM640T ZA (Panel LC320EUA PE F2), LG 32LS570T (Panel LC320EUN (SE)(M2)), LG 47LM620S (Panel LC470EUE (SE)(F4)), LG 42LM670T (Panel LC420EUG(PE)(F2)), LG 42LM640T 42LM640S (Panel LC420EUG (PE)(F1)), LG 42LM620T (Panel LC420EUE (SE)(F1)), LG 47LM660T (Panel LC470EUG (PE)(F1)), LG 42LS570T (Panel T420HVN01.0), LG 42LS570S ZB (Panel LC420EUE (SE)(M1)), LG 42LM669T (Panel LC420EUG (PE)(F2)), LG 42LM669S (Panel LC420EUG (PE)(F1)), LG 37LM620T (Panel LC370EUN (SE)(F2)), LG 47LM669 (Panel LC470EUG (PE)(F2)), LG 32LS570S ZB (Panel LC320EUN (SE)(M2)), LG 47LM620T (Panel LC470EUE (SE)(F3)), LG 47LM761T ZA (Panel LC470EUH (PE)(F1), LG 32LM620S (Panel LC320EUN (SE)(F2) ), LG 47LM670T 47LM670T-ZA.BRUWLJU (Panel LC470EUG (PE)(F1)), LG 42LM660S 42LM660S-ZA.BRUWLJU (Panel LC420EUG (PE)(F1)), LG 42LM660T 42LM660T-ZA.BRUWLJU (Panel LC420EUG (PE)(F1) ), LG 32LM620T (Panel LC320EUN (SE)(F3)), LG 55LM620T 55LM620T-ZE (Panel LC550EUE (SE)(F1)).
The appearance of the power supply
Main features of the device LG 42LM620S:
Installed matrix (LED-panel) LC420EUE (SE) (F1).
The matrix control uses the Timing Controller (T-CON) 6870C-0401B.
To power the backlight LEDs, a converter is used, combined with a power supply, controlled by a PWM controller R5F100BCAFP, AAT2430AISX. As power elements of the LED driver, keys of the PHT4NQ10LT type are used.
The necessary supply voltages for all nodes of the LG 42LM620S TV are generated by the EAX64427101 power module or its analogs using FAN7930BG (PFC), L6599AD (PWM), STR-A6059 (Stb) microcircuits and power switches of the STF13NM60N, STF10NM60N type.
MainBoard - the main board (motherboard) is an EAX64307906 module, using LCE2112, H5TQ2G63DFR, KLM2G1HE3F, MICOM R5F100GEA, 24C16 and other chips.
The TDSN-G351D tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: LG Display
Model: LC420EUE-SEF1
Type: a-Si TFT-LCD, Panel
Diagonal size: 42 inch
Resolution: 1920x1080, FHD
Display Mode: S-IPS, Normally Black, Transmissive
Active Area: 930.24x523.26 mm
Surface: Antiglare (Haze 1%), Hard coating (3H)
Brightness: 360 cd / m²
Contrast Ratio: 1400: 1
Display Colors: 16.7M (8-bit), CIE1931 68%
Response Time: 6 (G to G)
Frequency: 60Hz
Lamp Type: 6 strings WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 51 pins
Voltage: 12.0V