Technical description and composition of the PHILIPS 60PFL9607T TV, panel type and applicable modules. The composition of the modules.PHILIPS LED
Model: 60PFL9607T / 12
Chassis / Version: QFU1.1E LA
Panel: LK600D3LB63 (SRJ)
LED driver (backlight): integrated into PSU
Power Supply (PSU): FSP373-5F01 272217190742
MainBoard: 310431365664
IC MainBoard: FUSION120, H5TQ2G83BFR, H26M21001ECR, TAS5731P1
Tuner: SUT-RE214AN
Technical Specifications 60PFL9607T
PHILIPS 60PFL9607T
General repair guidelines for TV LCD LED
In the absence of any signs of operability, when the PHILIPS 60PFL9607T does not turn on and does not signal anything with the control lights on the panel, there is a possibility of a malfunction of the power supply module FSP373-5F01 272217190742 of the TV. When diagnosing and repairing the power supply, after replacing the swollen capacitors of the secondary rectifier filters (if any), you must first check the mains fuse. When it is broken, the power elements of transistors and rectifier bridge diodes should be checked for avalanche (thermal) breakdown.
The reasons for the breakdown of the power switch in switching power supplies (IIPS) can be different, for example, a malfunction of semiconductor cells or electrolytic capacitors in the stabilization circuits of the primary circuit, as well as a failure in the operation of the ICM Power PWM controller or broken resistors in its wiring.
If the PHILIPS 60PFL9607T TV does not have an image, but there is sound, there may be a malfunction in the backlight circuits of the LED panel LK600D3LB63 (SRJ) B.
Often in the absence of backlighting, disassembling the panel is required. It is necessary to check the serviceability of the transitions of the LEDs, as well as the reliability of the contact connections in the rulers and connectors.
It is impossible to check the line of series-connected LEDs without a special current source, and for this purpose it is not safe to use any voltage sources above 12V. Then it remains only to open the panel and check each LED separately. Usually, Chinese 9V-powered multimeters light up a single 3-volt LED, if you connect the probes in the forward direction, the red probe to the anode, and the black to the cathode. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of health. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
When trying to repair the motherboard, you should first check the serviceability of linear stabilizers or power converters of microcircuits and, if necessary, update the software (software).
In cases of attempts to repair the MB (SSB) board, it is necessary to check the health of its elements - CPU: FUSION240; NAND Flash: 29F8G08ABABA; DRAM: H5TQ2G63BFR; SOUND: TAS5731P1; SPI Flash: M25P05-AVMN6 (25P10); EEPROM: M24C64-WDW6 which may require replacement with new ones. If a BGA processor is installed, there is a possibility of a violation of the soldering of the contacts of its conclusions with the board (it is diagnosed by heating).
Before changing the SUT-RE214AN tuner, if it is not possible to tune to television channels, make sure that there are supply voltages that must be measured at the corresponding tuner pins and check the software for correctness. The pulses of the data exchange of the tuner with the processor can be controlled by an oscilloscope
Attention! For users and owners of 60PFL9607T TVs who do not have the appropriate qualifications, knowledge and experience, we categorically do not recommend attempting self-repair in order to avoid negative consequences that could lead to complete non-serviceability of the device.
The appearance of MainBoard 310431365664 is shown in the figure below:310431365664
310431365664 can be used in TVs:
PHILIPS 32PFL6007T/12 (Panel LC320EUF FEP1 code 423), PHILIPS 32PFL6008T/60 (Panel LC320EUF (FE)(P1) code 423), PHILIPS 32PFL6087T/12 (Panel LC320EUF (FE)(P1)), PHILIPS 32PFL6087T/12 (Panel LC320EUF FE P1), PHILIPS 42PFL6007T/60 (Panel LC420EUF (FE)(P1)), PHILIPS 42PFL6057T/60 (Panel LC420EUF FC P1), PHILIPS 42PFL6097T/60 (Panel LC420EUF (FE)(P1) code 322 p/n: 932228895682), PHILIPS 42PFL6877T/60 (Panel LC420EUF (FE)(P1)), PHILIPS 47PFL6057T/60 (Panel LC470EUF FE P1 (LG/PH) B code 323 p/n: 932228896682), PHILIPS 47PFL6097T/60 (Panel LC470EUF (FE)(P1)), PHILIPS 47PFL6877T/60 (Panel LC470EUF FE P1), PHILIPS 55PFL6007T/12 (Panel C550EUF (FE)(P1)), PHILIPS 60PFL9607T/12 (Panel LK600D3LB63 (SRJ)), PHILIPS 42PFL6067T/12 (Panel LC420EUF (FE)(P1)), PHILIPS 47PFL6007K/12 (Panel LC470EUF (FE)(P1)).
The appearance of the power supply
Main features of the PHILIPS 60PFL9607T device:
Installed matrix (LED panel) LK600D3LB63 (SRJ).
To power the backlight LEDs, a converter is used, combined with a power supply.
The necessary supply voltages for all nodes of the PHILIPS 60PFL9607T TV are generated by the FSP373-5F01 power supply module, or its analogs.
MainBoard - the main board (motherboard) is a module 310431365664, using chips FUSION120, H5TQ2G83BFR, H26M21001ECR, TAS5731P1 and others.
The SUT-RE214AN tuner provides TV reception and channel tuning.