Technical description and composition of the BBK 32LEM-1036 TV, type of panel and applicable modules. The composition of the modules.BBK LED
Model: 32LEM-1036 / TS2C
Chassis / Version: CV512H-B42
Panel: DS32D6AP0113
LED backlight: M00601066 DS32L61A-V01 DSBJ-WG = 202006-DS32M6F00-01 (26H-07) 160829D
T-CON: V320BJ6-Q01
LED driver (backlight): integrated into MainBoard
PWM LED driver: BIT3267
MOSFET LED driver: ME15N10
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MOSFET Power: SMK0760F
MainBoard: CV512H-B42
IC MainBoard: CPU: 9206B 1533-DBN, SPI Flash: 25Q64
Tuner: CDT-9NT372-RF01, CDT-9NS161-RD41
Control: Remote: RC-LEM100, RC-LEM2012, IR: 3228DHS-IR
Specifications 32LEM-1036 / TS2C
BBK 32LEM-1036
General repair guidelines for TV LCD LED
Possible malfunctions
- BBK 32LEM-1036 does not turn on, the indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
The malfunction in such cases should be sought in the elements of the power source - the network voltage converter (AC / DC), which is located on the MainBoard CV512H-B42 main board. It is necessary to measure its output voltages, and in case of their absence (full or partial), it is necessary to check the serviceability of power switches (SMK0760F) of converters and rectifier diodes for the presence of a possible short circuit.
In case of any breakdowns in the secondary circuits, the converter can operate in emergency short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse or the current sensor at the source of the key more often breaks.
Mos-Fet power switches, used in switching power supplies, sometimes fail due to a malfunction of any other elements that can put it out of operation in key mode or create an excess of the maximum permissible parameters of the switch. These can be elements supplying the PWM controller, frequency-setting or damping circuits, or negative feedback elements in the stabilization circuit. PWM SOT23-6 PWM controllers, in the absence of visible damage or obvious short-circuit between the terminals, are checked by replacing with new ones, or obviously working.
- There is no image, but there is sound, it reacts to the remote control. Or the image appears when you turn it on and immediately disappears
A malfunction is usually most likely in these cases at the backlight nodes of the display matrix. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
It is impossible to detect a break in the LED line without disassembling the panel with a simple multimeter. The LEDs are connected in series and to open their transitions, a voltage of several tens of volts is required. Ideally, a current source is suitable for such purposes. You can open the panel and check each LED separately. Typically, Chinese multimeters light up a single 3-volt LED, if you connect the probes in the forward direction to it (red probe to the anode, black to the cathode). In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of health. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the CV512H-B42 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its CPU chips: 9206B 1533-DBN, SPI Flash: 25Q64 and other possible faulty components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
Before replacing the tuner CDT-9NT372-RF01, CDT-9NS161-RD41, if there is no tuning for the channels, you must first check the software and the supply voltage at its terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus
Owners of 32LEM-1036 TVs are recommended to contact qualified specialists with the necessary work experience for repairs! Self-repair attempts without the appropriate knowledge and skills can lead to irreversible negative consequences!
Service manual and schematic diagram MainBoard --------------------> CV512H-B42-12
The appearance of the MainBoard CV512H-B42 is shown in the figure below:CV512H-B42
CV512H-B42 can be used in TVs:
BBK 40LEM-1010 / FT2C (Panel CX390DLEDM), BBK 32LEM-1023 / TS2C (Panel V320BJ6-Q01), BBK 32LEM-3035 / T2C (Panel LS320TU9A00 NJ), BBK 32LEM-1036 / TS2C (Panel DS32D6AP01M) 1009 / FT2C (Panel T420HVN06.1 CX420DLEDM), DEXP F40B7000E (Panel V400HJ6-PE1 CX400DLEDM).
Main features of the BBK 32LEM-1036 device:
Installed matrix (LED-panel) DS32D6AP0113.
The matrix control uses the Timing Controller (T-CON) V320BJ6-Q01.
To power the backlight LEDs, a converter is used, combined with the main board CV512H-B42, controlled by the BIT3267 PWM controller. As the power elements of the LED driver, keys of the type ME15N10 are used.
The power module is combined with the MainBoard and is designed according to a flyback AC / DC voltage converter using PWM SOT23-6 microcircuits and power switches of the SMK0760F type.
MainBoard - the main board (motherboard) is a CV512H-B42 module, using CPU chips: 9206B 1533-DBN, SPI Flash: 25Q64 and others.
The tuner CDT-9NT372-RF01, CDT-9NS161-RD41 provides the reception of television programs and tuning to channels.
Brand: BBK, Model: 32LEM-1036 / TS2C.
Briefly from the TV: LCD, 720p HD, 32 "(81 cm) diagonal, HDMI: 3 connectors, USB, DVB-T2 support, satellite tuner.
The composition uses MainBoard CV512H-B42 and LCD panel (matrix) DS32D6AP0113. The power supply is combined with the MainBoard.
BBK 32LEM-1036 / TS2C LED TV with DS32D6AP0113 LCD, 32 "(81 cm) diagonal size of 16: 9 format. The required screen brightness of 250 cd / m² is provided by LED backlighting. The ratio of maximum brightness to minimum (contrast) is 3000: 1. LED display technology is implemented in the model’s display technology. HD images can be viewed in high resolution at 1366x768 pixels in the standard of graphic decomposition 720p (HD Ready). Supported media file formats: MP3, WMA, MPEG4, MKV, JPEG .
The power of the sound system 16 W (2x8 W) provides two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, VGA, HDMI x3, USB. An output for connecting headphones is provided. The digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C MPEG4, DVB-T2, DVB-S2 standards.
Overall dimensions: With stand 733x479x215 mm, Without stand 733x436x80 mm.
TV mass: 6 kg.
Attention! The DS32D6AP0113 panel of the BBK 32LEM-1036 / TS2C LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.