Technical description and composition of the BBK 32LEX-5009 TV, panel type and applicable modules. The composition of the modules.BBK LED
Model: 32LEX-5009 / T2C
Chassis / Version: CV628H-T42
Panel: ST3151A05-8 CX315DLEDM
LED backlight: 01.JL.D3281235-06ES
T-CON: MT3151A05-5-XC-5
LED driver (backlight): integrated into MainBoard
PWM LED driver: BIT3267
MOSFET LED driver: AOD4454
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6 (LD7536)
MOSFET Power: SMK10N60
MainBoard: CV628H-T42
IC MainBoard: CPU: MSD6A628VXM-ST, NAND: KLM4G1FEPD, SPI FLASH: Winb25Q16JVSIQ, AUDIO: TPA3110LD2
Tuner: CDT-9NT372-RF01 (MSB102KT)
Specifications 32LEX-5009 / T2C
BBK 32LEX-5009
General repair guidelines for TV LCD LED
Possible malfunctions
- BBK 32LEX-5009 does not turn on and does not show any signs of performance at all. Does not blink indicators and does not respond to control buttons.
In such cases, the common power source, the AC / DC voltage converter, which is combined with the elements of the CV628H-T42 main board, is often faulty. Then we recommend that you measure its output voltages and, if they are absent, you should check the health of the power switches (SMK10N60) and the rectifier diodes of the converters for possible short-circuit.
In case of breakdowns of semiconductors in the secondary circuits of any converter, as a rule, it can operate in emergency short-circuit mode without output voltages, and during short circuit in the elements of the primary circuit, the main fuse and, less often, the current sensor at the source of the key are most often cut off.
Mos-Fet power switches, used in switching power supplies, sometimes fail due to a malfunction of any other elements that can put it out of operation in key mode or create an excess of the maximum permissible parameters of the switch. These can be elements supplying the PWM controller, frequency-setting or damping circuits, or negative feedback elements in the stabilization circuit. PWM SOT23-6 (LD7536) PWM controllers, in the absence of visible damage or frank short-circuit between the terminals, are checked by replacing with new ones, or obviously working.
- There is no image, but there is sound and reaction to the remote control. Or for a second, the image may appear immediately after switching on.
The most likely in these cases is a malfunction of the LED backlight. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
It is impossible to check the line of series-connected LEDs without a special current source, and for this purpose it is not safe to use any voltage sources above 12V for them. Then it remains only to open the panel and check each LED separately. Usually, Chinese 9V-powered multimeters light up a single 3-volt LED, if you connect the probes in the forward direction, the red probe to the anode, and the black to the cathode. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of health. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The TV does not enter the operating mode, does not respond to the remote control. The indicator on the front panel lights constantly or blinks.
Repair or diagnostics of the CV628H-T42 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). When repairing an MB board, you need to check its CPU components: MSD6A628VXM-ST, NAND: KLM4G1FEPD, SPI FLASH: Winb25Q16JVSIQ, AUDIO: TPA3110LD2. Defective items should be replaced. If chips with BGA soldering technology are used, a problem in its implementation is detected by the local heating of the chip.
The malfunction of the tuner CDT-9NT372-RF01 (MSB102KT) is established after checking the software and all the supply voltages at its terminals. The data exchange of the tuner with the processor via the I2C bus can be controlled by an oscilloscope.
Attention! For users and owners of 32LEX-5009 TVs who do not have the appropriate qualifications, knowledge and experience, we categorically do not recommend attempting self-repair in order to avoid negative consequences that could lead to complete non-repairability of the device.
1. Service Manual with Schematic Diagram 91 pages of 2015 on model ------------------> 32LEX-5009 / T2C
2. Service Manual with Schematic Diagram 52 pages 2015 models: ------------------> 28LEM-1012/T2C, 32LEM-1005/T2C, 32LEM-1007/T2C, 32LEM-1010/T2C, 32LEM-3025/T2C, 32LEX-5009/T2C, 40LEM-1010/FT2C, 40LEM-1007/FT2C, 40LEM-1005/FT2C, 40LEM-1010/T2C, 40LEM-1017/T2C, 40LEM-3025/FT2C, 40LEM-3035/FT2C, 40LEX-5009/FT2C, 43LEM-1007/FT2C, 43LEM-1009/FT2C, 43LEX-5009/FT2C, Rubin RB-32D7T2S
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> BBK 32LEX-5009 Chassis CV628H-T42
The appearance of the MainBoard CV628H-T42 is shown in the figure below:CV628H-T42
CV628H-T42 can be used in TVs:
BBK 43LEX-5009/FT2C (Panel LC430DUY (SH)(A1)), BBK 40LEX-5025/FT2C (Panel V400HJ6-PE1 DLEDSV400FHD), BBK 32LEX-5027/T2C (Panel V320BJ6-Q01 Rev.C1), SUPRA STV-LC40ST900FL (Panel V400HJ6-PE1).
Main features of the BBK 32LEX-5009 device:
Installed matrix (LED panel) ST3151A05-8 CX315DLEDM.
The matrix control uses the Timing Controller (T-CON) MT3151A05-5-XC-5.
To power the backlight LEDs, a converter is used, combined with the main board CV628H-T42, controlled by a BIT3267 PWM controller. As power elements of the LED driver, keys of the AOD4454 type are used.
The power module is combined with the MainBoard and is made according to the flyback AC / DC voltage converter circuit using PWM SOT23-6 (LD7536) microcircuits and SMK10N60 type power switches.
MainBoard - the main board (motherboard) is a CV628H-T42 module, using CPU chips: MSD6A628VXM-ST, NAND: KLM4G1FEPD, SPI FLASH: Winb25Q16JVSIQ, AUDIO: TPA3110LD2 and others.
The tuner CDT-9NT372-RF01 (MSB102KT) provides the reception of television programs and tuning to channels.
Brand: BBK, Model: 32LEX-5009 / T2C.
Briefly from the TV: LCD, 720p HD, 32 "(81 cm) diagonal, Smart TV (Android), Wi-Fi, HDMI: 3, USB: 3, there is support for DVB-T2, backlight type: Edge LED.
The composition uses MainBoard CV628H-T42 and LCD-panel ST3151A05-8 CX315DLEDM. The power supply is combined with the MainBoard.
BBK 32LEX-5009 / T2C LED TV with ST3151A05-8 LCD display, 32 "(81 cm) diagonal size in 16: 9 format. The required screen brightness of 250 cd / m² is provided by LED backlight LED. The ratio of maximum brightness to minimum ( contrast ratio) is 1400: 1. This model uses side illumination from Edge LEDs. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard of graphic decomposition 720p (HD Ready).
32LEX-5009 / T2C has built-in SMART Software and pre-installed Android Operating System. Connecting to the Internet can be done via Wi-Fi. The input high-frequency or video signal can be processed in analogue systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i. Supported media file formats: MP3, WMA, MPEG4, MKV, JPEG.
The power of the sound system 10 W (2x5 W) provides two speakers. It uses a NICAM stereo signal processing system and Sound Surround.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, component, SCART, VGA, HDMI x3, MHL, USB x3, Ethernet (RJ-45), Wi-Fi 802.11n. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768. The digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C MPEG4, DVB-T2 standards.
Overall dimensions: With stand 737x472x160 mm, Without stand 737x438x77 mm.
TV Weight: 6.3 kg.
Attention! The BBK 32LEX-5009 / T2C LED TV panel ST3151A05-8 CX315DLEDM is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.