Technical description and composition of the BBK LED2272FDTG TV, type of panel and applicable modules. The composition of the modules.BBK LED
Model: LED2272FDTG
Panel: V215H1-LE1 RevC1
Trans LED driver: B6010D
Power Supply (PSU): L-CEM1
PWM Power: LD7535 (PWM 6 pin)
MainBoard: L0M04 (01) 20011.09.16
Control: RC-LED100
Technical Specifications LED2272FDTG
BBK LED2272FDTG
General repair guidelines for TV LCD LED
Possible malfunctions
- BBK LED2272FDTG does not turn on, the indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
Most often, with such manifestations, the L-CEM1 main power module turns out to be faulty. It is necessary to measure the secondary output supply voltages, and in case of their absence, check the serviceability of the power switches of the converters and rectifier diodes for a short circuit.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during a short circuit in the elements of the primary circuit, the mains fuse usually breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. It can be supply, damper circuits, or elements of OOS (negative feedback) stabilization. The reason for the breakdown of the power key may be PWM (PWM) LD7535 (PWM 6 pin). It is checked only by replacement with a known good one.
- There is no image, there is sound, it responds to the remote. Or the image may appear for a second when turned on and immediately disappears.
Usually in such cases, a malfunction is detected in the backlight nodes of the LED panel. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
It is impossible to check the line of series-connected LEDs without a special current source, and for this purpose it is not safe to use any voltage sources above 12V. Then it remains only to open the panel and check each LED separately. Usually, Chinese 9V-powered multimeters light up a single 3-volt LED, if you connect the probes in the forward direction, the red probe to the anode, and the black to the cathode. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of health. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The indicator blinks or lights constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the L0M04 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software).
Attention to users! Independent repair of the BBK LED2272FDTG TV without the appropriate qualifications and the necessary experience can lead to its complete non-repairability!
The appearance of the MainBoard L0M04 is shown in the figure below:L0M04
The appearance of the power supply
Main features of the BBK LED2272FDTG device:
Installed matrix (LED panel) V215H1-LE1 RevC1. The transformer B6010D is installed in the LED driver converter.
The necessary supply voltages for all nodes of the BBK LED2272FDTG TV are generated by the L-CEM1 power module or its analogs using LD7535 microcircuits (PWM 6 pin).
MainBoard - the main board (motherboard) is an L0M04 module.
Additional technical information about the panel:
Brand: CMO
Model: V215H1-LE1
Type: a-Si TFT-LCD, Panel
Diagonal size: 21.5 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 476.64x268.11 mm
Surface: Antiglare (Haze 25%)
Brightness: 250 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (8-bit), CIE1931 70%
Response Time: 1.3 / 3.7 (Tr / Td)
Frequency: 60Hz
Lamp Type: 13S6P WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V
Brand: BBK, Model: LED2272FDTG.
Briefly from the TV: LCD, 1080p Full HD, diagonal 23 "(58 cm), HDMI: 2, USB, backlight type: Edge LED.
The composition uses MainBoard L0M04 (01) and the LCD panel (matrix) V215H1-LE1 RevC1.
Power Supply Unit (PSU) L-CEM1 Power Supply.
BBK LED TV LED2272FDTG with V215H1-LE1 LCD, 23 "(58 cm) diagonal, 16: 9 format. The required screen brightness of 250 cd / m² is provided by LED backlighting. The ratio of maximum brightness to minimum (contrast) is 1000 : 1. This model uses Edge LED backlighting, and the design and technical features of the TV include watching broadcasts and movies in high quality HD at a resolution of 1920x1080 pixels in graphic resolution according to the standard 1080p (Full HD). l can be processed in analog systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Supported media file formats: MP3, WMA, MPEG4, MKV, VideoCD , SVCD, Picture CD, JPEG.
The power of the acoustic system of sound 6 W (2x3 W) provide two speakers. It uses a NICAM stereo signal processing system and Sound Surround.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, VGA, HDMI x2, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768, 1920x1080. The digital tuner is capable of receiving television channels in DVB-T MPEG4 standards.
The power consumed by the TV in the operating mode from the network is 35 watts.
Overall dimensions: 550x405x125 mm.
The mass of the TV: 5.3 kg.
Attention! The BBK LED2272FDTG V215H1-LE1 RevC1 panel is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.