Technical description and composition of the BBK LED2473FDTW TV, type of panel and applicable modules. The composition of the modules.BBK LED
Model: LED2473FDTW
Panel: LC230EUE (TD) (A1)
LED driver (backlight): LDA15-63V240K
Power Supply (PSU): FSE060A 1 REV1
PWM Power: PWM SOT23-6
MainBoard: L0M04 (01) 1202T0170 88XR-LOMO04012473DT
IC MainBoard: MSD309PX-LF-Z1, Winbond 25Q32, YD1517
Tuner: NoName
Control: RC-LED100
Technical Specifications LED2473FDTW
BBK LED2473FDTW
General repair guidelines for TV LCD LED
Possible malfunctions
- BBK LED2473FDTW does not turn on, the indicators on the front panel do not light or flash. The TV does not respond to the control buttons and the remote control.
In the vast majority of such cases, a malfunction is detected in the FSE060A power supply module. It is necessary to measure its secondary output voltages, and in case of their absence, check the serviceability of the power switches of the converters and rectifier diodes for a short circuit.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during a short circuit in the elements of the primary circuit, the mains fuse usually breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke the excess of maximum current or voltage values. It can be supply, damper circuits, or elements of OOS (negative feedback) stabilization. The reason for the breakdown of the power switch may be PWM (PWM). It is checked only by replacement with a known good one.
- There is no image, there is sound, it responds to the remote control. Or the image may appear for a second when turned on and immediately disappears.
In most cases, the malfunction is caused by the lack of a backlight display. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It is impossible to check the LED line for breaks without disassembling the panel with a multimeter or tester. For these purposes, it is necessary to open all series-connected PN junctions and a voltage of the order of tens of volts will be required, and ideally, a current source. Having disassembled the panel, it is necessary to check each LED separately. Chinese multimeters, as a rule, light up a single 3-volt LED in the forward direction. In the case of using dual 6-volt LEDs, the PN junction of its protective zener diode can serve as a health indicator. In faulty LEDs, the zener diode will either be cut off or broken into short-circuit.
- The TV does not turn on, the indicator indicates standby or operating mode, or blinks.
Repair or diagnostics of the L0M04 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software).
Attention! For users and owners of LED2473FDTW TVs who do not have the appropriate qualifications, knowledge and experience, we categorically do not recommend attempting self-repair in order to avoid negative consequences that could lead to complete non-repairability of the device.
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> BBK LED1973W LED2273FW LED2473FW (MST182VG + 2IN1 POWER SUPPLY)
The appearance of the MainBoard L0M04 is shown in the figure below:L0M04
The appearance of the power supply
Main features of the BBK LED2473FDTW device:
Installed matrix (LED-panel) LC230EUE (TD) (A1).
The LED driver LDA15-63V240K is used to power the backlight LEDs.
The necessary supply voltages for all nodes of the TV BBK LED2473FDTW are generated by the FSE060A power module, or its analogs using PWM SOT23-6 microcircuits.
MainBoard - the main board (motherboard) is an L0M04 module, using microchips MSD309PX-LF-Z1, Winbond 25Q32, YD1517 and others.
The NoName tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: LG Display
Model: LC230EUE-TDA1
Type: a-Si TFT-LCD, Panel
Diagonal size: 23.0 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 509.184x286.416 mm
Surface: Antiglare, Hard coating (3H)
Brightness: 250 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (8-bit)
Response Time: 1.3 / 3.7 (Tr / Td)
Frequency: 60Hz
Lamp Type: 2 strings WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V
Brand: BBK, Model: LED2473FDTW.
Briefly from the TV: LCD, 1080p Full HD, diagonal 24 "(61 cm), HDMI: 2, USB, backlight type: Edge LED.
The composition uses MainBoard L0M04 (01) and LCD panel (matrix) LC230EUE (TD) (A1).
Power Supply Unit (PSU) FSE060A 1 REV1 Power Supply.
BBK LED2473FDTW LED TV with LC230EUE LCD, 24 "(61 cm) diagonal size in 16: 9 format. The required screen brightness of 250 cd / m² is provided by LED backlighting. The ratio of maximum brightness to minimum (contrast) is 1000: 1 This model uses side illumination from Edge LEDs.The design and technical capabilities of the TV include watching programs and movies in high quality HD with a resolution of 1920x1080 pixels in graphic resolution according to the standard 1080p (Full HD). Input high-frequency or video signal can be processed in analogue systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Supported media file formats: MP3, WMA, MPEG4, MKV, VideoCD, SVCD, Picture CD, JPEG.
The power of the acoustic system of sound 6 W (2x3 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, VGA, HDMI x2, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768, 1920x1080. The digital tuner is capable of receiving television channels in DVB-T MPEG4 standards.
The power consumed by the TV in the operating mode from the network is 40 watts.
Overall dimensions: 589x425x125 mm.
TV Weight: 4.5 kg.
Attention! The BB2 LED2473FDTW LCD TV panel LC230EUE (TD) (A1) is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.