Technical description and composition of the BBK LEM2296F TV, panel type and applicable modules. The composition of the modules.BBK LED
Model: LEM2296F
Chassis / Version: S228NY0EORD
Panel: CE21M21A RVE.01
PWM LED driver: FSE040A2
Power Supply (PSU): FSE040A2
MainBoard: 88XR-E182VG-2296
Technical Specifications LEM2296F
BBK LEM2296F
General repair guidelines for TV LCD LED
Possible malfunctions
- BBK LEM2296F does not turn on at all and does not show any signs of operability. Does not blink indicators and does not respond to control buttons.
Often in such cases, the FSE040A2 power module is faulty. It is necessary to measure the secondary output supply voltages, and in case of their absence, check the serviceability of the power switches of the converters and rectifier diodes for a short circuit.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during short circuit in the elements of the primary circuit, the mains fuse usually breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke an excess of the maximum current or voltage. It can be supply, damper circuits, or elements of OOS (negative feedback) stabilization. The reason for the breakdown of the power switch may be PWM (PWM). It is checked only by replacement with a known good one.
- There is no image, there is sound, it is responding to the remote control. Or immediately after turning on for a second, the image may appear and immediately disappear.
In most cases, the malfunction is caused by the lack of a backlight display. The reason for this may be a break in the LED circuit, or a problem in stabilizing their power supply.
When trying to detect a break in the LED lines, it should be taken into account that it is difficult to do this without disassembling the panel. For example, a current source is needed to open PN junctions connected in series.
- The indicator blinks or lights constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the 88XR-E182VG-2296 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software).
Once again, remind users! Attempts to self-repair a BBK LEM2296F TV without the appropriate qualifications and the necessary experience can lead to its complete non-repairability!
Service Manual with Schematic Diagram 32 pages for model -------------> LEM1993, LED1994, LEM1995, LEM1996, LEM1997, LEM2293F, LED2294F, LEM2295F, LEM2296F, LEM2297F, LEM2493F, LED2494F, LEM2495F, LEM2496F, LEM2497F, LEM2993, LED2994, LEM2995, LEM2996, LEM2997, LED2253FW, LED1952DTG, LED2252FDTG, LED2452FDTG, LED2278F
The appearance of the MainBoard MSTV2407-ZC01-01 is shown in the figure below:
MSTV2407-ZC01-01
MSTV2407-ZC01-01 motherboard is combined with a power module. The processor is MST6E182VG, or MST6E181VG, made using BGA technology. Repair of the power module is carried out according to conventional technology, starting with checking its power elements. The following is a functional check of the converters for the processor power: + 1.3V, + 1.8V, 3.3V, based on the SY8008B PWM controllers. The power supply of the built-in DDR 2.5V is generated from a 3.3V source using the P-N junction of the 1N4001 diode (3.3V-0.8V = 2.5V). Standby mode is organized from the linear stabilizer series 1117-3V3. The LCD panel is powered by either 5V or 12V, depending on the type of panel used.
MSTV2407-ZC01-01 can be used in TVs:
BBK LEM2249HD Ver2 (Panel LM215DT5D), BBK LEM2284F (Panel M215HG-LE4 Rev.C3), BBK LEM2681F (Panel V260H1-LE10 Rev. C1 ), BBK LEM2682 LEM2682DT (Panel V260B2-LE11 Rev.C1), BBK LEM3284F (Panel HV320WXC-200), Haier LE32T1000 (Panel T320XVN09.0), MYSTERY MTV-2224LW (Panel M215HG-LE4 Rev.C3), MYSTERY MTV-3222LW (Panel T320XVN01.0), MYSTERY MTV-1924LW (Panel V185B1-L17), MYSTERY MTV-3018LW (Panel V290BJ1-PE1), MYSTERY MTV-1911LW (Panel HT185WX7-100), MYSTERY MTV-1922LW (Panel V185B1-L17), MYSTERY MTV-1913LW (Panel HT185WX7-100), MYSTERY MTV-3218LW (Panel HV320WX2-20A), MYSTERY MTV-1918LW (Panel V185B1-L17), MYSTERY MTV-2213LW (Panel M215HGE-L10), MYSTERY MTV-2222LW (Panel M215HG-LE4 REV.C3), MYSTERY MTV-2418LW (Panel HM236WUA-100), MYSTERY MTV-2424LW (Panel HM236WU8-100), MYSTERY MTV-1914LW (Panel V185B1-L15 Rev.c1), MYSTERY MTV-3223LW (Panel LK315T3HB94), MYSTERY MTV-2422LW (Panel HM236WU8–100), MYSTERY MTV-3224LW (Panel T320XVN09.0), MYSTERY MTV-2218LW (Panel CLAA215FA10), MYSTERY MTV-1911WL (Panel V185B1-L15 REV.C1), MYSTERY MTV-3221LW (Panel HV320WX2-268), MYSTERY MTV-2211W (Panel M215HG-LE4 ).
Main features of the BBK LEM2296F device:
Installed matrix (LED panel) CE21M21A RVE.01.
A converter controlled by the FSE040A2 PWM controller is used to power the backlight LEDs.
The formation of the necessary supply voltages for all nodes of the BBK LEM2296F TV is carried out by the FSE040A2 power module, or its analogs.
MainBoard - the main board (motherboard) is a 88XR-E182VG-2296 module.