Technical description and composition of the LG 47LA690V TV, panel type and applicable modules. The composition of the modules.LG LED
Model: 47LA690V ZB
Chassis / Version: LD33B
Panel: LC47EUH (PF) (P1)
LED driver (backlight): integrated into PSU
PWM LED driver: R5F100BCAFP, IW7011
MOSFET LED driver: TK15A20D
Power Supply (PSU): EAX64905701 LGP4247-13LPB
PWM Power: SSC9527S, R2A20133D (PFC), ICE3BR4765JZ (Stb)
MOSFET Power: 13NM60N, 10NM60N
MainBoard: EAX64797003 EBR76823176
IC MainBoard: CPU: LGE2122, TPS65178, TPS65198, NAND: SAA36403538 VER. 3.20.33 H5TQ4G63AFR x2 H5TQ2G63AFR NTP7513
Tuner: TSQ-G601D (B)
Specifications 47LA690V
LG 47LA690V
General repair guidelines for TV LCD LED
Possible manifestations of defects
- LG 47LA690V TV does not turn on at all. There is no reaction to the remote control and control buttons from the front panel. Indicator lights do not light or flash.
With such manifestations, a malfunction is most likely to be detected in the EAX64905701 power module. It is necessary to measure its output voltages and, if they are absent, to check for short-circuit probabilities in the converters, power switches (13NM60N, 10NM60N) and rectifier diodes.
In the event of a breakdown in the secondary circuits of the converter, it can usually fail in short circuit mode, and in case of a short circuit in the power elements of the primary circuit, the mains fuse or current sensor at the source of the key most often breaks.
Mos-Fet power switches, used in switching power supplies, sometimes fail due to a malfunction of any other elements that can put it out of operation in key mode or create an excess of the maximum permissible parameters of the switch. These can be elements supplying the PWM controller, frequency-setting or damping circuits, or negative feedback elements in the stabilization circuit. PWM controllers SSC9527S, R2A20133D (PFC), ICE3BR4765JZ (Stb), in the absence of visible damage or explicit short-circuit between the terminals, are checked by replacing with new, or obviously working.
- There is no image, but there is sound, it reacts to the remote control. Or the image appears when you turn it on and immediately disappears
In some of these cases, the malfunction is caused by a lack of backlighting on the display. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
It should be remembered that it is not possible to determine the open circuit in the LED lines without disassembling the panels with a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required. Then it is necessary to open the panel and check each LED separately with a multimeter. If the capabilities of your multimeter do not allow you to open the LED in the forward direction or dual LEd are used, then the PN junction of the emergency zener diode can indirectly serve as a health indicator. In case of LED-a failure, the zener diode PN junction will either be cut off or broken into short-circuit.
- The TV does not turn on, the indicator indicates standby or operating mode, or blinks.
Repair or diagnostics of the EAX64797003 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). When repairing an MB board, you need to check its CPU components: LGE2122, TPS65178, TPS65198, NAND: SAA36403538 VER. 3.20.33 H5TQ4G63AFR x2 H5TQ2G63AFR NTP7513. Defective items should be replaced. If chips with BGA soldering technology are used, a problem in its implementation is detected by the local heating of the chip.
Before replacing the tuner TSQ-G601D (B), if there is no tuning for the channels, you must first check the software and the supply voltage at its terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus
Attention! For users and owners of 47LA690V TVs who do not have the appropriate qualifications, knowledge and experience, we strongly recommend against attempting self-repair in order to avoid negative consequences that could lead to complete non-repairability of the device.
Service manual and schematic diagram --------------> 47LA6918, 47LA6928, 47LA690S, 47LA690V, 47LA691S, 47LA691V CHASSIS_LD33B.
schematic diagram --------------> EAX64905701 LGP4247-13LPB
The appearance of the MainBoard EAX64797003 is shown in the figure below:EAX64797003
EAX64797003 can be used in TVs:
LG 42LA620V (Panel LC420DUE (SF)(U1)), LG 32LN570V (Panel LC320DUE (SF)(R1)), LG 50LA644V (Panel LC500EUN (SF)(F1)), LG 47LA660V (Panel LC470EUG (PF)(F1)), LG 47LA621V (Panel LC470DUE (SF)(U1)), LG 42LA644V (Panel LC420EUN (SF)(F2)), LG 39LA620V ZA (Panel T390HVJ01.0), LG 42LA621V ZD (Panel LC420DUE (SF)(U1)), LG 32LA621V ZD (Panel LC320DUE (SF)(U1)), LG 32LN655V (Panel LC320EUB (PF)(M1)), LG 42LA667V (Panel LC420EUH (PF)(P1) ), LG 47LN613V (Panel LC470DUE (SF)(R4)), LG 32LA667V ZB (Panel LC320EUB (PF)(P1)), LG 55LA660V ZA (Panel LC550EUH (PF)(P1)), LG 47LA620V ZA (Panel LC470DUE (SF)(U1)), LG 32LN613V ZB (Panel LC320DUE (SF)(R4)), LG 42LN655V ZB.BRUZLJU (Panel LC420EUH (PF)(M1)), LG 32LA644V ZA (Panel LC320EUN (SF)(F1)), LG 42LN613V (Panel LC420DUE (SF)(R4)), LG 47LA690V ZB (Panel LC47EUH (PF)(P1)), LG 47LA662V (Panel LC470EUG (PF)(F1)), LG 42LA645V 42LA645V-ZC.BRUYLJU (Panel LC420EUN (SF)(F3)), LG 32LA660V (Panel LC320EUB (PF)(P1)), LG 47LA644V 47LA644V-ZA (Panel LC470EUN (SF)(F2)), LG 50LA667S (Panel T500HVD02.1), LG 47LA691V (Panel LC470EUH (PF)(P1)), LG 32LA662V (Panel LC320EUB (PF)(P1)).
The appearance of the power supply
Main features of the device LG 47LA690V:
Installed matrix (LED-panel) LC47EUH (PF) (P1).
To power the backlight LEDs, a converter is used, combined with a power supply unit, controlled by a PWM controller R5F100BCAFP, IW7011. As the power elements of the LED driver, keys of the TK15A20D type are used.
The necessary supply voltages for all nodes of the LG 47LA690V TV are generated by the EAX64905701 power supply module or its analogs using SSC9527S, R2A20133D (PFC), ICE3BR4765JZ (Stb) microcircuits and 13NM60N, 10NM60N type power switches.
MainBoard - the main board (motherboard) is an EAX64797003 module using CPU chips: LGE2122, TPS65178, TPS65198, NAND: SAA36403538 VER. 3.20.33 H5TQ4G63AFR x2 H5TQ2G63AFR NTP7513 and others.
The TSQ-G601D (B) tuner allows you to receive television programs and tune to channels.