Technical description and composition of the TV SHARP LC-24CHG5112E, type of panel and applicable modules. The composition of the modules.SHARP LED
Model: LC-24CHG5112E LC-24CHG5112EW
Chassis / Version: TP.MS3463S.PA511
Panel: V236BJ1-P01
LED backlight: CRH-P2360141404511-rev1.0 ZC
T-CON: INNOLUX XC V236BJ1-P01
LED driver (backlight): integrated into MainBoard
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6
MOSFET Power: TO-252
MainBoard: TP.MS3463S.PA511
Tuner: CDT-9NT372-RF01
Control: IR: SPAD_402Rx + LED Light-V02
Technical Specifications LC-24CHG5112EM
SHARP LC-24CHG5112E
General repair guidelines for TV LCD LED
Possible manifestations of defects
- The SHARP LC-24CHG5112E TV does not turn on, does not respond to the remote control and the control panel buttons, the indicators do not light or flash.
In such cases, the main power source - the AC / DC voltage converter, which is combined with the MainBoard TP.MS3463S.PA511 board, may turn out to be faulty. It is necessary to verify the presence of its output voltages and, if they are completely absent, check the power switches (TO-252) and rectifier diodes for a probable short circuit.
In case of any breakdowns in the secondary circuits, the converter can operate in emergency short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse or the current sensor at the source of the key more often breaks.
Mos-Fet keys used in switching power supplies usually fail due to a malfunction of other elements that can put it out of operation in key mode or provoke the excess of maximum current or voltage values. These can be circuits supplying the PWM controller, damping or frequency-setting circuits, or elements of OOS (negative feedback) in the stabilization circuit. PWM controllers (PWM) PWM SOT23-6, in the absence of external damage and short circuit between the terminals, are checked by replacing with obviously good ones.
- There is no image, but there is sound, it reacts to the remote control. Or the image appears when you turn on and immediately disappears
In some of these cases, the malfunction is caused by a lack of backlighting on the display. The reason can be both in the power of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
When trying to detect a break in the LED lines, it should be taken into account that it is difficult to do this without disassembling the panel. For example, a current source is needed to open PN junctions connected in series.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the TP.MS3463S.PA511 motherboard should begin by checking the stabilizers and power converters needed to power the microcircuit and matrix. If necessary, update or replace the software (software).
Before replacing the tuner CDT-9NT372-RF01, if there is no tuning for the channels, you must first check the software and the supply voltage at its terminals. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus
Attention to users! Self-repair of the SHARP LC-24CHG5112E TV without the appropriate qualifications and the necessary experience can lead to its complete non-repairability!
FIRMWARE SPI FLASH ----------> SHARP LC-24CHG5112E LC-24CHG5112EW, Main: TP.MS3463S.PA511, Panel: V236BJ1-P01
The appearance of MainBoard TP.MS3463S.PA511 is shown in the figure below:TP.MS3463S.PA511
Main features of the SHARP LC-24CHG5112E device:
Installed matrix (LED-panel) V236BJ1-P01.
The matrix control uses the Timing Controller (T-CON) INNOLUX.
To power the backlight LEDs, a converter is used, combined with the main board TP.MS3463S.PA511.
The power module is combined with the MainBoard and is made according to the flyback AC / DC voltage converter circuit using PWM SOT23-6 microcircuits and TO-252 type power switches.
MainBoard - the main board (motherboard) is a module TP.MS3463S.PA511.
The tuner CDT-9NT372-RF01 provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: CHIMEI INNOLUX
Model: V236BJ1-P01
Type: a-Si TFT-LCD, CELL
Diagonal size: 23.6 inch
Resolution: 1366x768, WXGA
Display Mode: MVA, Normally Black, Transmissive
Active Area: 521.471x293.184 mm
Surface: Antiglare (Haze 1%), Hard coating (3H)
Glass Depth: 0.50 + 0.50 mm
Transmissivity: 5.5% (with Polarizer)
Contrast Ratio: 3000: 1
Display Colors: 16.7M (8-bit), CIE1931 72%
Response Time: 8.5 (G to G)
Frequency: 60Hz
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 12.0V