Monday 9 March 2020

REPAIR / SERVICING TV SONY KDL-46V3000

Technical description and composition of the TV SONY KDL-46V3000, type of panel and applicable modules. The composition of the modules.
SONY
Model: KDL-46V3000
Chassis / Version: FIX2
Panel: 46 inch
Inverter (backlight): DF2, DF3
Power Supply (PSU): 1-873-813-14 (1-873-813-13) GF1 + DF1
PWM Power: L6562 (PFC), CXD9841P, MIP2H2
MainBoard: HV2, AU, TUU3
Control: RM-YD014
Technical Specifications KDL-46V3000
SONY KDL-46V3000
General recommendations for repairing TV LCD
It is advisable to start the repair and diagnostics of the SONY KDL-46V3000 TV with a careful external examination of the internal and external elements, including case parts, a display, buttons and cables. In some cases, visible external damage to the elements can suggest directions for troubleshooting and localizing the defect before starting the necessary measurements at the control points of the nodes of electronic circuits. Swollen electrolytic or cermet capacitors, charred resistors, ring cracks in the soldered terminals of the elements - all this can significantly help the master to determine the causes and consequences of the malfunction of the TV.
Sometimes the SONY KDL-46V3000 TV simply does not turn on. No control lights on the front panel are lit or blinking, the TV does not respond to the remote control and does not make any sounds or any signs of life when turned on. The most likely cause of the malfunction is the failure of the common power module GF1. If the mains fuse is broken in the power supply, in most cases a breakdown of the power switch is detected, which can be integrated with the PWM controller, or a separate field-effect transistor can be used. The rectifier bridge diodes and the electrolytic capacitor of the mains rectifier filter should also be checked.
The reasons for the breakdown of the power switch of the flyback converter of the power module can be different, for example, a malfunction of semiconductor elements or electrolytic capacitors in the stabilization circuits of the primary circuit, as well as a failure in the operation of the PWM controller chip or breakage of the resistors in its bundle.
In cases where the Power Factor Corrector (PFC) is used in the power supply, troubleshooting can be a bit more complicated.
In cases where the SONY KDL-46V3000 TV has lost an image, and the sound is there and all other functions are operational, there is a possibility of an inverter (converter for powering the backlight) malfunction. When you turn on the TV, the image may appear briefly and immediately disappear. It must be borne in mind that with such manifestations, the lamps themselves also fail, the malfunction of which can be detected by replacement, by connecting to the connectors for diagnostics that are known to be serviceable and suitable in power.
Repair of the inverter DF2, DF3 is complicated by the fact that in case of any malfunction or emergency, even with uneven wear of the lamps, a protection is triggered, which turns it off for fire safety. Diagnostics become impossible and protection needs to be disabled.
It should be remembered that when the protection is turned off, there is always a risk of failure of the power elements of the inverter during diagnosis. After repair, it is necessary to restore all standard converter protection circuits.
On the motherboard HV2, AU, TUU3, in the event of a malfunction, you should first check the operation of all the power stabilizers of the microcircuits and, if necessary, update the software (software).
We recommend the owners of the KDL-46V3000 TV for repair only to qualified specialists with experience! Self-repair attempts without the appropriate knowledge and skills can lead to serious negative consequences!


Service manual / schematic diagram ------------->   Sony KDL-40V3000, KDL-46V3000, KDL-46VL130 chassis FIX2 


 The appearance of the power supply
Main features of the device SONY KDL-46V3000:
Installed matrix (LCD-panel) 46 inches.
To power the backlight used inverter DF2.
The necessary supply voltages for all nodes of the SONY KDL-46V3000 TV are generated by the power module 1-873-813-14, or its analogs using microcircuits L6562 (PFC), CXD9841P, MIP2H2.
MainBoard - the main board (motherboard) is an HV2 module.