Thursday 9 April 2020

REPAIR / SERVICING TV AIWA 47LE71113

Technical description and composition of the TV AIWA 47LE71113, type of panel and applicable modules. The composition of the modules.
AIWA LED
Model: 47LE71113
Chassis / Version: V1N03 chassis 8M51B
Panel: LC470EUJ-SFK2 (SEL470FY)
LED driver (backlight): 168P-P47DWM-W2 5800-P47DWM-W200 VER00.00
Power Supply (PSU): 168P-P47ELL-W1 5800-P47ELL-W000
PWM Power: TEA1752 (PFC + PWM)
MOSFET Power: 18N50, 2SK3673
MainBoard: 5800-A8M51B-0000 Ver00.07
IC MainBoard: CPU: MSD6329SV, Eeprom: K24C04, SPI Flash: 25L1606E (MX25L1605A), NAND Flash: TC58NVG1S3ETA00
Tuner: TDST-G070D
Specifications 47LE71113
AIWA 47LE71113
General repair guidelines for TV LCD LED
Possible manifestations of defects
- AIWA 47LE71113 TV does not turn on at all. There is no reaction to the remote control and control buttons from the front panel. Indicator lights do not light or flash.
Failure in such cases should begin to be sought in the power supply circuits of 168P-P47ELL-W1. It is necessary to measure its output voltages and, in case of their absence, check the serviceability of power switches (18N50, 2SK3673) and rectifier diodes in the converters for possible breakdown.
In case of breakdowns in the secondary circuits, the converter, as a rule, can emergency work in the short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse usually breaks.
Breakdown of power switches (MosFet) in pulsed sources is sometimes caused by malfunctions of other circuit elements, for example, in circuits supplying a PWM controller, frequency-setting or damper ones, as well as in negative feedback (OOS) stabilization circuits. PWM controllers (PWM) TEA1752 (PFC + PWM), if they do not have visible damage to the case and open fault between the terminals, are usually checked by replacement.
- There is no image, there is sound, it is responding to the remote control. Or immediately after turning on for a second, the image may appear and immediately disappear.
As a rule, in such cases there is no display backlight. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To check the LED strips, to open all the transitions of the LEDs, several tens of volts or more are needed, it is best to use a current source for such purposes. The breakage of several PN junctions connected in series cannot be detected with a multimeter or tester. In such cases, it is necessary to open the panel and check each LED. If your multimeter cannot open the LED transitions in forward bias, you can sometimes detect the presence of a PN junction of the protective zener diode by connecting the probes in the opposite direction. If the zener diode is broken or broken in short-circuit, then the LED is faulty and needs to be replaced.
- The indicator blinks or lights constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the 5800-A8M51B-0000 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its CPU chips: MSD6329SV, Eeprom: K24C04, SPI Flash: 25L1606E (MX25L1605A), NAND Flash: TC58NVG1S3ETA00 and other possible faulty components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
If a TDST-G070D tuner is suspected of malfunction, first of all, it is necessary to verify the correctness of the software, as well as the presence of the necessary supply voltage levels and data exchange pulses with the processor via the I2C bus on the corresponding tuner pins.
Owners and users of the AIWA 47LE71113 TV should remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!


SCHEMATIC DIAGRAM  / SERVICE MANUAL   ------------------>    168P-P47ELL ... 5800-P47ELL ... Power supply

FIRMWARE FOR SPI FLASH  ----------->   AIWA 47LE71113 V1N03, Main: 5800-A8M51B-0000, Panel: LC470EUJ-SFK2

FIRMWARE FOR SPI FLASH  ----------->   AIWA 47LE71113 V1M12 , Main: 5800-A8M51B-0000



   The appearance of the MainBoard 5800-A8M51B-0000 is shown in the figure below:
5800-A8M51B-0000
5800-A8M51B-0000 can be used in TVs:
AIWA 47LE71113 (Panel LC470EUJ-SFK2 (SEL470FY)), AIWA 32LE7011 (Panel REL320HY (LD0-000) Rev:00).
The appearance of the power supply
Key Features of AIWA 47LE71113:
Installed matrix (LED panel) LC470EUJ-SFK2 (SEL470FY).
The LED driver 168P-P47DWM-W2 is used to power the backlight LEDs.
The necessary supply voltages for all nodes of the TV AIWA 47LE71113 are generated by the 168P-P47ELL-W1 power supply module or its analogs using TEA1752 microcircuits (PFC + PWM) and power switches of the 18N50, 2SK3673 type.
MainBoard - the main board (motherboard) is a 5800-A8M51B-0000 module, using CPU chips: MSD6329SV, Eeprom: K24C04, SPI Flash: 25L1606E (MX25L1605A), NAND Flash: TC58NVG1S3ETA00 and others.
The TDST-G070D tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: LG Display
Model: LC470EUJ-SFK2
Type: a-Si TFT-LCD, CELL
Diagonal size: 47 inch
Resolution: 1920x1080, FHD
Display Mode: IPS, Normally Black, Transmissive
Active Area: 1039.68x584.82 mm
Surface: Antiglare (Haze 1%), Hard coating (2H)
Glass Depth: 0.50 + 0.50 mm
Transmissivity: 5.87% (with Polarizer)
Contrast Ratio: 1200: 1
Display Colors: 16.7M (8-bit)
Response Time: 6 (G to G)
Frequency: 60Hz
Signal Interface: LVDS (2 ch, 8-bit), 51 pins
Voltage: 12.0V

 Trademark: AIWA, Model: 47LE71113.
Briefly from the TV: LCD, LED backlight, 47 ", 1920x1080, 1080p Full HD, 3D, sound: 24W, HDMI: 4, Wi-Fi, Smart TV.
The composition includes MainBoard 5800-A8M51B-0000 Ver00.07 and LCD panel (matrix) LC470EUJ-SFK2 (SEL470FY).
Power Supply Unit (PSU) 168P-P47ELL-W1 5800-P47ELL-W000 Power Supply.
AIWA 47LE71113 TV with LC470EUJ-SFK2 LCD display, 47 "(119 cm) diagonal size in 16: 9 format. The required screen brightness of 360 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 120,000: 1 is achieved by special control of the LEDs. V manufacturing technology of the display of this model implemented LED backlight.
There is support for 3D images with active (shutter) technology for separating the right and left channels.
The LC470EUJ-SFK2 (SEL470FY) panel and the 5800-A8M51B-0000 motherboard software provide for watching programs and movies in high quality HD at a resolution of 1920x1080 pixels in a graphical decomposition according to the standard 1080p (Full HD).
47LE71113 is equipped with SMART software and the ability to work on the Internet. Connecting to a network can be done via Wi-Fi. The input high-frequency or video signal can be processed in analogue systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p.
Supported media file formats: MP3, WMA, MPEG4, MKV, JPEG.
The power of the sound system 24 W (2x12 W) provides two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, VGA, HDMI x4, USB x2, Wi-Fi. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1280x1024, 1360x768, 1920x1080.
Overall dimensions: without stand 1024x639x62 mm.
Attention! Panel LC470EUJ-SFK2 (SEL470FY) LED-TV AIWA 47LE71113 is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.