Technical description and composition of the ERISSON 32LES80T2 TV, panel type and applicable modules. The composition of the modules.ERISSON LED
Model: 32LES80T2
Chassis / Version: 5800-A6M31G-0P10
Panel: LC320DXJ (SH) (A2)
LED backlight: CRH-A323030020759PREV1.1 I
LED driver (backlight): integrated into MainBoard
PWM LED driver: MP3398A
MOSFET LED driver: AOD4286
Power Supply (PSU): integrated into MainBoard
PWM Power: LNK6778K
MainBoard: 5800-A6M31G-0P10 VER: 00.01
IC MainBoard: SPI Flash: 25Q64CSIG, SOUND: TPA3113D2
Tuner: NoName
Control: IR: 5800-RUE300-1P0C
Specifications 32LES80T2
ERISSON 32LES80T2
General repair guidelines for TV LCD LED
Possible malfunctions
- The ERISSON 32LES80T2 TV does not turn on and does not show any signs of operability at all. There is no reaction to the remote control and control buttons from the front panel.
The malfunction in such cases, first of all, should be sought in the power elements of a switching power supply (IIP) - a network voltage converter (AC / DC), which in this TV model is combined with the MainBoard 5800-A6M31G-0P10 main board. Then we recommend that you measure its output voltages and, if they are absent, you should check the health of the power switches and rectifier diodes of the converters for a probable short circuit.
In case of any breakdowns in the secondary circuits, the converter can operate in emergency short circuit mode, and during short circuit in the power elements of the primary circuit, the mains fuse or the current sensor at the source of the key more often breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. PWM circuits (PWM) LNK6778K are usually checked by replacing with new, or obviously working.
- There is no image, there is sound, it responds to the remote control. Or the image may appear for a second when turned on and immediately disappears.
The faulty usually in these cases is the backlight matrix (LED-panel). More often the reason for this is the breakdown of the LEDs, or poor contact in the connectors of the strips, less often the LED driver may be faulty.
When diagnosing, it is necessary to take into account that it is impossible to check the open in the chain of LED lines without disassembling the panels using a tester or multimeter. To open all PN junctions connected in series, a voltage of the order of several tens of volts is required, and ideally, a current source. By opening the panel, each LED can be checked separately. Typically, Chinese multimeters light up a single 3-volt LED, if you connect probes in the forward direction to it. In dual 6-volt LEDs, the PN junction of its emergency zener diode can serve as an indicator of health. In the event of a LED malfunction, its zener diode will either be cut off or broken into short-circuit.
- The indicator on the front panel blinks, the TV does not turn on in the operating mode, it does not respond to the remote control.
Repair or diagnostics of the 5800-A6M31G-0P10 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Board repair and chip replacement SPI Flash: 25Q64CSIG, SOUND: TPA3113D2 are made with the necessary equipment, and the corresponding element base. Faults associated with the application of BGA processor soldering technologies can be localized by the heating method.
If the TV works normally from external devices, but does not tune into television channels, the NoName tuner may be malfunctioning. In such cases, first of all, you should make sure that there are supply voltages at its corresponding conclusions. It is also necessary to make sure that the tuner and processor can exchange data via the I2C bus. Sometimes the cause of the inoperability of the tuner may be a software failure.
For owners of 32LES80T2 TVs, we recommend that you contact qualified specialists with the necessary work experience for repairs! Self-repair attempts without the appropriate knowledge and skills can lead to irreversible negative consequences!
FIRMWARE FOR SPI FLASH -----------> ERISSON 32LES80T2, Main: 5800-A6M31G-0P10 VER:00.01, Panel: LC320DXJ (SH)(A2)
To reduce the backlight current, the total resistance of the resistors relative to the housing on the ISET pin of the MP3398A should be proportionally increased. ISET (current setting) - pin 8 in the SOIC-20 package or pin 6 in the SOIC-16 package.
Repair MainBoard
The appearance of the MainBoard 5800-A6M31G-0P10 is shown in the figure below:
5800-A6M31G-0P10
5800-A6M31G-0P10 can be used in TVs:
AIWA 32LE4020 (Panel LC320DXJ-SHA2 GDL320HY (LD0-008) Rev.00), AIWA 32LE7020 (Panel LC320DXJ (SH)(A2)), ERISSON 32LES71T2 (Panel LC320DXJ-SFA2), ERISSON 32LES70T2 (Panel LC320DXJ (SF)(A2)), SUPRA STV-LC32T650WL (Panel LC320DXJ-SFA2 RDL320HY(LD0-803)45).
Main features of the ERISSON 32LES80T2 device:
Installed matrix (LED-panel) LC320DXJ (SH) (A2).
To power the backlight LEDs, a converter is used, combined with the main board 5800-A6M31G-0P10, controlled by the MP3398A PWM controller. As power elements of the LED driver, keys of the AOD4286 type are used.
The power module is combined with the MainBoard and is made according to the flyback AC / DC voltage converter circuit using LNK6778K microcircuits.
MainBoard - the main board (motherboard) is a 5800-A6M31G-0P10 module, using SPI Flash chips: 25Q64CSIG, SOUND: TPA3113D2 and others.
The NoName tuner provides television reception and channel tuning.
Trademark: ERISSON, Model: 32LES80T2.
Briefly from the TV: LCD, 720p HD, 32 "(81 cm) diagonal, HDMI: 3, USB, DVB-T2 support, backlight type: Edge LED.
The composition uses MainBoard 5800-A6M31G-0P10 VER: 00.01 and LCD-panel LC320DXJ (SH) (A2). Power supply combined with MainBoard.
Technical description
TV ERISSON 32LES80T2 with LCD LC320DXJ, diagonal size 32 "(81 cm) 16: 9 format. The required brightness of the screen 200 cd / m² is provided by LED backlight LED. Contrast, as the ratio of maximum brightness to minimum, is 1200: 1. The LED panel of this TV has an end LED backlight - Edge LED. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard of graphic decomposition 720p (HD Ready). Supported media file formats: MP3, WMA, MPEG4, MKV, JPEG .
The power of the sound system 12 W (2x6 W) provide two speakers. It uses a NICAM stereo signal processing system and Sound Surround.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), component, VGA, HDMI x3, USB. An output for connecting headphones is provided.
A digital tuner is capable of receiving television channels in the DVB-T MPEG4, DVB-C, DVB-T2 standards.
Overall dimensions: With stand 730x526x179 mm, Without stand 735x434x87 mm.
Attention! The LC320DXJ (SH) (A2) panel of an ERISSON 32LES80T2 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable