Technical description and composition of the HYUNDAI H-LEDVD32V6 TV, panel type and applicable modules. The composition of the modules.HYUNDAI LED
Model: H-LEDVD32V6
Chassis / Version: T.MS6M181.6A
Panel: V320BJ2-P01 // V320BJ3-P01
MainBoard: T.MS6M181.6A
IC MainBoard: CPU: MST6E181VS-LF-Z1, W9425G6JH-4, FLASH: MX25L3206E
Technical Specifications H-LEDVD32V6
HYUNDAI H-LEDVD32V6
General repair guidelines for TV LCD LED
It is advisable to start the repair of the HYUNDAI H-LEDVD32V6 TV with a careful external examination of both internal and external elements. Sometimes, based on visible changes in the components of the device, it is possible to draw some conclusions and determine the direction of further troubleshooting even before the necessary measurements are taken. Elements with visible damage, for example, capacitors swelled up after boiling the electrolyte, charred resistors in certain nodes of the circuit, as well as ring cracks in solders will help the master to guess the causes and possible consequences of the malfunction.
If the H-LEDVD32V6 TV does not turn on, does not make any sounds when turned on, and also no indicators on the front panel light or blink - there is a high probability of a malfunction in the power module. In some cases, only the stabilizer or power converter of the control processor may be faulty, which is typical for some HYUNDAI models. It is advisable to start the troubleshooting of the power supply module by checking the state of the electrolytic capacitors of the rectifier filters and the mains fuse. Defective capacitors should be replaced. If the mains fuse is broken, it is necessary to check first of all the power semiconductor elements - rectifier diodes and transistors, which are often found in such a state of breakdown.
It should be borne in mind that in the practice of repair it is extremely rare that key transistors in switching power supplies (SMPS) fail for no reason that should be sought by checking other components, for example, a breakdown of the key can provoke faulty elements of the damper circuits, or dried electrolytic capacitors or dangling primary resistors BP circuits involved in the stabilization process. In this case, all semiconductor elements of the strapping of the PWM controller chip are subject to verification, which it is desirable to verify by replacement.
If there is no image when you turn on the HYUNDAI H-LEDVD32V6, or it appears for a second and disappears, but there is sound, most likely there is a malfunction in the backlight LED circuit of the V320BJ-P01 panel, or in their power converter. It is necessary to check the electrolytic capacitors of the filter of the secondary rectifiers in the general power supply unit.
Often there is a need for disassembling the panel to check the health of the LEDs, as well as contact connections in the connectors and soldering.
It should be remembered that it is not possible to determine the open circuit in the LED lines without disassembling the panels with a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required.
When trying to repair the motherboard, you should first check the serviceability of linear stabilizers or power converters of microcircuits and, if necessary, update the software (software).
Often, the MB (SSB) card must be replaced in case of complex malfunctions that are difficult to detect. When trying to repair, you should check its elements - CPU: MST6E181VS-LF-Z1, W9425G6JH-4, FLASH: MX25L3206E and replace failed chips with new ones. Some malfunctions may be due to the use of BGA soldering technologies in modern Main Board technologies. Typically, such defects are detected by local heating of the chip.
Owners of the H-LEDVD32V6 TV are recommended to repair only qualified specialists with experience! Self-repair attempts without the appropriate knowledge and skills can lead to serious negative consequences!
FIRMWARE FOR SPI FLASH -----------> HYUNDAI H-LEDVD32V6, Main: T.MS6M181.6A, Panel V320BJ-P01
The appearance of MainBoard T.MS6M181.6A is shown in the figure below:Repairing the motherboard T.MS6M181.6A, which uses the multi-function processor MST6M181VS, combined with a scaler, it is advisable to start by checking the power supply of the standby mode (Stand-by), which is implemented using a separate linear stabilizer 3.3V. Further, in the operating mode, it is necessary to check the operability of linear stabilizers or voltage converters necessary to provide power to the processor nodes: 1.2V, 2.5V, 3.3V. A voltage of 2.5V is required to power the DDR W9425G6JH memory. If there is a backlight and no image, the power of the LCD panel 5V or 12V, depending on the type of panel used, it is advisable to measure directly on the LVDS connector. If the TV does not exit Stand-by, does not respond to the remote control and control buttons, update the SPI FLASH software.
T.MS6M181.6A can be used in TVs:
AKAI LTA-32L09P (Panel LTA320AP05), ERISSON 32LEN60 (Panel LTA320AN01 D02 ), ERISSON 32LEE01 (Panel 720p HD 1366x768), HAIER LE32Z50 (Panel T315XW06 V5), Hyundai H-LED32V6 (Panel HV320WXC-100), HYUNDAI H-LEDVD32V6 (Panel V320BJ2-P01), HYUNDAI H-LED32V16 (Panel CX315LEDM).
Main features of the HYUNDAI H-LEDVD32V6 device:
Installed matrix (LED-panel) V320BJ2-P01 or V320BJ3-P01.
The required supply voltage for all nodes of the HYUNDAI H-LEDVD32V6 TV is provided by a switching power supply.
MainBoard - the main board (motherboard) is a T.MS6M181.6A module, using CPU chips: MST6E181VS-LF-Z1, W9425G6JH-4, FLASH: MX25L3206E and others.
Additional technical information about the panel:
Brand: CHIMEI INNOLUX
Model: V320BJ2-P01
Type: a-Si TFT-LCD, CELL
Diagonal size: 31.5 inch
Resolution: 1366x768, WXGA
Display Mode: MVA, Normally Black, Transmissive
Active Area: 697.685x392.256 mm
Surface: Antiglare (Haze 11%), Hard coating (3H)
Glass Depth: 0.70 + 0.70 mm
Transmissivity: 5.8% (with Polarizer)
Contrast Ratio: 3000: 1
Display Colors: 16.7M (8-bit)
Frequency: 60Hz
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 12.0V
HYUNDAI H-LEDVD32V6 TV with V320BJ2-P01 LCD, 32 "(81 cm) diagonal size of 16: 9 format. The required screen brightness of 400 cd / m² is provided by LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 4000: 1. Edge LED backlighting is implemented in the LED panel of this TV - Edge LED. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard for graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Supported media file formats: MP3, WMA, MPEG4, Xvid, DivX, VideoCD, SVCD, Picture CD, JPEG.
The power of the sound speaker system 16 W (2x8 W) is provided by two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, VGA, HDMI x3, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
The power consumed by the TV in the operating mode from the network is 85 watts.
Overall dimensions: 785x537x230 mm.
The mass of the TV: 10 kg.
Attention! The panel V320BJ2-P01 of the HYUNDAI H-LEDVD32V6 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.