Technical description and composition of the MYSTERY MTV-2614LW TV, type of panel and applicable modules. The composition of the modules.MYSTERY LED
Model: MTV-2614LW
Chassis / Version: MSTV3208-ZC01-01
Panel: V260H1-LE6 // V260H1-LE7
LED backlight: LED26R / L-ZC14-06 (A)
LED driver (backlight): TV2631-ZC02-01 (B)
PWM LED driver: RT8566
MOSFET LED driver: B6010D
Power Supply (PSU): TV2632-ZC02-01 (A) // TV2632-ZC02-02 (A)
PWM Power: SG6848
MainBoard: MSTV3208-ZC01-01
IC MainBoard: CPU: MST6M48RHS-LF-Z1, RAM: H5P95162FFR
Tuner: F21WT-3BAR-E
Technical Specifications MTV-2614LW
MYSTERY MTV-2614LW
General repair guidelines for TV LCD LED
It is advisable to start the repair of the MYSTERY MTV-2614LW TV with a careful external examination of both internal and external elements. According to some external signs of a change in the state of some elements, it is sometimes possible to make assumptions about the nature of the defect, as well as determine the further direction of the troubleshooting. Experienced repairmen are often aware of the causes of the defect and the possible consequences, for example, from ring cracks in the soldering of the leads of the elements, as well as from swollen capacitors or resistors burnt to coal dust and other external indirect signs.
If the TV does not turn on, no indicators on its front panel are lit or blinking. Also, if the TV does not respond to the remote control and buttons, it does not make any sounds or any signs of operability when turned on, there is a certain chance that the TV2632-ZC02-01 (A) power supply module is defective and needs repair. Sometimes with similar manifestations a problem can only occur in the absence of processor power, which is typical for certain MYSTERY models. When diagnosing and repairing the power supply, first of all, replace the swollen capacitors of the filter of the secondary rectifiers and check the fuse and, if it is broken, it is necessary to identify the cause. Often in such cases, an avalanche (thermal) breakdown is detected in the power semiconductor elements of the module — rectifier diodes and transistors in the primary circuit.
The reasons for the breakdown of the power switch in switching power supplies (IIPS) can be different, for example, a malfunction of semiconductor cells or electrolytic capacitors in the stabilization circuits of the primary circuit, as well as a failure in the operation of the PWM controller SG6848 or broken resistors in its bundle.
If the MYSTERY MTV-2614LW TV does not have an image, but there is sound, a malfunction in the LED backlight circuits of the V260H1-LE6 panel is likely. It is also necessary to check the serviceability of the electrolytic capacitors of the filter of the secondary rectifiers of the PSU (power supply) for an overstated ESR.
Often there is a need for disassembling the panel to check the health of the LEDs, as well as contact connections in the connectors and soldering.
When diagnosing, it is necessary to take into account that it is impossible to check the open in the chain of LED lines without disassembling the panels using a tester or multimeter. To open all PN junctions connected in series, a voltage of the order of several tens of volts is required, and ideally, a current source.
If the motherboard MSTV3208-ZC01-01 is faulty, first of all it is necessary to check all the linear stabilizers or power converters of its chips, and also, if necessary, update the software. Sometimes you can check the health of MB only by replacement.
Board repair and replacement of CPU chips: MST6M48RHS-LF-Z1, RAM: H5P95162FFR are carried out with the necessary equipment, and the corresponding element base. Faults associated with the application of BGA processor soldering technologies can be localized by the heating method.
Before replacing the F21WT-3BAR-E tuner, if there is no tuning for the channels, you must first check the power supply voltage at its terminals, including the power supply of varicaps (30-33V).
For MTV-2614LW TV owners, we recommend that you contact qualified personnel with experience to repair! Self-repair attempts without the appropriate knowledge and skills can lead to serious negative consequences!
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> MYSTERY Main MSTV3208-ZC01-01
FIRMWARE FOR SPI FLASH -----------> MYSTERY MTV-2614LW, Main MSTV3208-ZC01-01, Panel V260H1-LE6
To reduce the backlight current in LED drivers with an RT8566 controller, it is necessary to proportionally increase the resistance of the resistor from terminal 2 (RISET) to the housing. The current in each channel is determined from the 543.6 / Rset ratio.
Repair MainBoardThe appearance of the MainBoard MSTV3208-ZC01-01 is shown in the figure below:
The motherboard MSTV3208-ZC01-01 is made using the multifunction microprocessor MST6M48RHS-LF, which includes a scaler (graphic controller-scaler). To organize the work of the processor, the external RAM H5PS5162GFR 512Mb DDR2 SDRAM in BGA version and SPI FLASH 25Q32 (4Mb) are used. To provide power to the processor core, a DC / DC converter with an output voltage of 1.2V is used, assembled on the basis of the MP1482 PWM controller. Other nodes of the processor are powered by linear voltage stabilizers 2.5V, 3.3V. 1.8V voltage is used to power the DDR RAM, 3.3V is needed for the SPI FLASH ROM.
It is advisable to start the MainBoard repair by checking the supply voltage in Stand-by mode 5V and 3.3V. In operating mode, check the operation of all linear stabilizers and the DC / DC converter. If there is a backlight and there is no image, you need to check the power of the 5V or 12V panel (depending on the type of LCD panel), which should be present directly on the LVDS connector.
If the indicator signals Stand-by mode and does not respond to the remote control and control buttons, it is recommended to update the SPI Flash software. Taking into account the glitchiness of Winbond SPI chips, it is advisable to replace them with new ones in case of software failures.
MSTV3208-ZC01-01 can be used in TVs:
BBK LEM2648SD (Panel V260B1-LE9 revC1), BBK LEM3248SD (Panel HV320WX2-130 (B3)), BBK LMP3229HDU Ver1 (Panel T315HW02 v.7), BBK LMP3229HDU Ver2 (Panel T315HW04 V7), BBK LEM2649HD (Panel V260H1-LE7 Rev C1), MYSTERY MTV-2607W (Panel V260H1-L05), MYSTERY MTV-3206 (Panel T315XW04 V.7), MYSTERY MTV-3207W (Panel V315B3-L04 rev.c1), MYSTERY MTV-3213LW (Panel T315XW04 V.8), MYSTERY MTV-2220LW (Panel CLAA215FA15), MYSTERY MTV-3207W (Panel HV320WX2-110), MYSTERY MTV-2614LW (Panel V260H1-LE6), MYSTERY MTV-3208WH (Panel V315H1-L02), MYSTERY MTV-2411LW (Panel V236H1-LE5 Rev.C1), MYSTERY MTV-2618LW (Panel V260B2-LE11), MYSTERY MTV-2211LW (Panel CLAA215FA10), MYSTERY MTV-2414LW (Panel V236H1-L01), MYSTERY MTV-2611LW (Panel V260H1-LE6 Rev.C1), MYSTERY MTV-3206W (Panel T315XW03 V.3), MYSTERY MTV-3211LW (Panel V315H3-LE2 Rev. C1), MYSTERY MTV-4207WH (Panel T420HW09 V.1), MYSTERY MTV-1921LD (Panel HT185WX3).
Main features of the MYSTERY MTV-2614LW device:
Installed matrix (LED-panel) V260H1-LE6 or V260H1-LE7.
To power the backlight LEDs, the TV2631-ZC02-01 (B) LED driver is used, controlled by the RT8566 PWM controller. As power elements of the LED driver, keys of the type B6010D are used.
The necessary supply voltages for all nodes of the MYSTERY MTV-2614LW TV are generated by the TV2632-ZC02-01 (A) power module, or its analogs using SG6848 microcircuits.
MainBoard - the main board (motherboard) is an MSTV3208-ZC01-01 module, using CPU chips: MST6M48RHS-LF-Z1, RAM: H5P95162FFR and others.
The F21WT-3BAR-E tuner provides television reception and channel tuning.
MYSTERY MTV-2614LW TV with V260H1-LE6 LCD, 26 "(66 cm) diagonal size 16: 9 format. The required screen brightness of 250 cd / m² is provided by LED backlighting. Contrast, as the ratio of maximum brightness to minimum, is 1000: 1. The LED-panel of this TV has end-face LED illumination - Edge LED.The TV design and technical features include viewing programs and movies in high quality HD at a resolution of 1920x1080 pixels in graphic resolution according to the standard 1080p (Full HD). frequency or video signal can be processed in analogue systems PAL, SECAM, NTSC. Graphic processing and digital signal generation occurs in standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p. Supported media file formats: MP3, DivX, JPEG.
The power of the acoustic system of sound 6 W (2x3 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, VGA, HDMI x2, USB. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 800x600, 1024x768.
The power consumed by the TV in the operating mode from the network is 40 watts.
Dimensions: With stand 642x444x209 mm, Without stand 570x345x70 mm.
Attention! The V260H1-LE6 panel of the MYSTERY MTV-2614LW LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.