Technical description and composition of the FUSION FLTV-15W5 TV, panel type and applicable modules. The composition of the modules.FUSION LED
Model: FLTV-15W5
Chassis / Version: V1J04
Panel: BT156GW01 V.6
T-CON: BT156GW01-C2-E
LED driver (backlight): integrated into T-CON
Power Supply (PSU): Adapter 12V
MainBoard: CVMV26L-A-20
IC MainBoard: CPU: TSUMV26KE-LF, SPI FLASH: F40-100GCP, EEPROM: K24C32
Tuner: F21WT-3BAR-E
Technical Specifications FLTV-15W5
FUSION FLTV-15W5
General repair guidelines for TV LCD LED
Possible manifestations of defects
- The FUSION FLTV-15W5 TV does not turn on and does not show any signs of operability at all. There is no reaction to the remote control and control buttons from the front panel.
Typically, with such manifestations, the defect is caused by faulty elements in the main power supply adapter.
The owner of the TV can purchase an external power supply unit such as Adapter and repairing it is not always advisable. In any case, the simplest typical defects characteristic of most IIP schemes can be easily detected and eliminated after opening. It is necessary to measure its output voltages, and in case of their absence (full or partial), it is necessary to check the serviceability of the power switches of the converters and rectifier diodes for the presence of a possible short circuit.
In case of breakdowns in the secondary circuits, the converter can operate in a short circuit mode, and during short circuit in the elements of the primary circuit, the mains fuse usually breaks.
The breakdown of Mos-Fet keys used in pulsed sources is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency-setting or damping circuits, as well as in Negative Stabilization Feedback. PWM microcircuits are usually checked by replacement with new ones, or obviously working.
- There is no image, there is sound, it responds to the remote control, the channels are switched. In some cases, the image appears when you turn on and immediately disappears.
In such cases, the most likely malfunction of the LED backlight elements. The reason can be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To check the LED lines for breaks without disassembling the panel, for example, a current source will help. It is impossible to open series-connected PN junctions with a simple multimeter, a voltage of the order of several tens of volts is required.
- The indicator blinks or lights constantly, the TV does not turn on, does not respond to the remote control.
Repair or diagnostics of the CVMV26L-A-20 motherboard should begin by checking the stabilizers and power converters needed to power the chips and matrix. If necessary, update or replace the software (software). Board repair and replacement of CPU chips: TSUMV26KE-LF, SPI FLASH: F40-100GCP, EEPROM: K24C32 are carried out with the necessary equipment, and the corresponding element base. Faults associated with the application of BGA processor soldering technologies can be localized by the heating method.
If you suspect a F21WT-3BAR-E tuner malfunction, first of all, you need to verify the correctness of the software, as well as the presence of the necessary voltage levels and data exchange pulses with the processor via the I2C bus at the corresponding tuner pins.
Owners and users of the FUSION FLTV-15W5 TV should remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!
Repair MainBoardThe appearance of the MainBoard CVMV26L-A-20 is shown in the figure below:
CVMV26L-A-20
The CVMV26L-A-20 motherboard uses the TSUMV26KE-LF processor (TSUMV36KE-LF), combined with a scaler, SPI FLASH 520Kb ROM and EEPROM 24C02C.
It is advisable to begin repairing the MainBoard by checking the voltage converters and linear stabilizers necessary to provide power in the operating and standby modes. Check the power supply of the 5V or 12V LCD panel, depending on the type of panel used, it is necessary to measure directly on the LVDS connector. If, in the presence of the necessary supply voltage, the TV does not exit Stand-by mode, does not respond to the remote control and control buttons, the SPI Flash software should be updated.
CVMV26L-A-20 can be used in TVs:
SUPRA STV-LC1926WD (Panel M185XW01 V0), SUPRA STV-LC1922WD (Panel MT185GW01 V.0), SUPRA STV-LC2222WD (Panel CLAA215FA), SUPRA STV-LC2622WD (Panel MT215DW01), SUPRA STV-LC1626WD (Panel 720p HD 1600x900), SUPRA STV-LC2417F STV-LC2417FD (Panel M236H1-P01), SUPRA STV-LC1515WD (Panel 720p HD 1366x768), SUPRA STV-LC2422W (Panel M236M1-L01), SUPRA STV-LC2422WD (Panel Panel), THOMSON T24C99H CVMV26L-A (Panel M236H1-L01 Rev.C2).
Main features of the FUSION FLTV-15W5 device:
Installed matrix (LED panel) BT156GW01 V.6.
The matrix control uses the Timing Controller (T-CON) BT156GW01-C2-E.
An integrated LED driver is used to power the backlight LEDs.
To power all internal nodes of the FUSION FLTV-15W5 TV, an external adapter 12V type is used.
MainBoard - the main board (motherboard) is a CVMV26L-A-20 module, using CPU chips: TSUMV26KE-LF, SPI FLASH: F40-100GCP, EEPROM: K24C32 and others.
The F21WT-3BAR-E tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: INNOLUX
Model: BT156GW01 V.6 16 Compatible model
Type: a-Si TFT-LCD, Panel
Diagonal size: 15.6 inch
Resolution: 1366x768, WXGA
Display Mode: TN, Normally White, Transmissive
Active Area: 344.232x193.536 mm
Shape Style: Wedge (PCBA Bent, Depth? 5.2mm)
Surface: Glare (Haze 0%), Hard coating (3H)
Brightness: 220 cd / m²
Contrast Ratio: 600: 1
Display Colors: 262K (6-bit), CIE1931 60%
Response Time: 8 (Tr + Td)
Frequency: 60Hz
Lamp Type: 9S6P WLED Embedded (LED Driver)
Signal Interface: LVDS (1 ch, 6-bit), 40 pins
Voltage: 3.3V