Technical description and composition of the FUSION FLTV-32W5 TV, panel type and applicable modules. The composition of the modules.Fusion
Model: FLTV-32W5
Chassis / Version: 471-01A3-32202G
Panel: LC320WXE (SB) (B1)
MainBoard: 471-01A3-32202G
IC MainBoard: SPI Flash: 24C64; EEPROM: EN25P16;
Tuner: CDT-3FP2I2-01
Technical Specifications FLTV-32W5
FUSION FLTV-32W5
General recommendations for repairing TV LCD
Repair of electronic equipment usually begins with its external inspection and diagnosis of the malfunction. In this case, you should examine all the internal components of the FUSION FLTV-32W5 TV, as well as the external elements of the housing. Specific external damage to some elements can sometimes indicate further actions to determine the malfunction of the TV and localize the defect before the necessary measurements are taken. If charred resistors, swollen electrolytic or cermet capacitors, ring cracks in the solders of the terminals of transformers or heating elements are detected, it is advisable to establish the causes and consequences of the malfunction that has arisen, as well as to check the connected elements and assemblies.
If the FLTV-32W5 TV does not turn on, does not make any sounds when turned on, and also no indicators on the front panel light or blink - there is a high probability of a malfunction in the power module. In some cases, there may be a malfunction only in standby power. In the absence of swollen filter capacitors of the secondary rectifiers, the diagnostics of the power supply should be started by checking the fuse and, if it is broken, it is first necessary to check all the power semiconductor elements of the primary circuit - diodes and transistors for the possibility of an avalanche or thermal breakdown.
It should be remembered that in the practice of repair, usually the power switches in switching power supplies (SMPS) do not fail due to their poor quality and, in such cases, it is necessary to look for the cause that led to a malfunction and provoked a breakdown of the key. Most often, the culprits of the accident are dried electrolytic capacitors or dangling resistors in the primary circuit, or the PWM controller chip itself may be faulty. It is also necessary to check all the semiconductor elements of the stabilization circuit in the primary and secondary circuits.
In cases where the FUSION FLTV-32W5 TV has lost an image, and the sound is there and all other functions are operational, there is a possibility of a malfunction of the inverter (converter for powering the backlight). When you turn on the TV, the image may appear briefly and immediately disappear. It must be borne in mind that with such manifestations, the lamps themselves also fail, the malfunction of which can be detected by replacement, by connecting to the connectors for diagnostics that are known to be serviceable and suitable in power. When disabling protection in order to enable the diagnosis of a malfunction, special care should be taken, and after completion of all repair work, it is necessary to restore the circuit and the inverter protection for further safe operation of the TV.
On the motherboard 471-01A3-32202G, in case of a malfunction, you should first check the performance of all the stabilizers and power converters of the microcircuits, and also, if necessary, update the software (software). In cases of complex repairs of MB (SSB) and in the presence of the necessary skills and equipment, sometimes it may be necessary to replace its SPI Flash chips: 24C64; EEPROM: EN25P16; and other possible malfunctioning components. Malfunctions associated with the application of BGA soldering technologies are usually easily diagnosed by the heating method.
Owners and users of the FUSION FLTV-32W5 TV must remember that self-repair without special knowledge, skills and qualifications can be fraught with negative consequences that can lead to complete non-repairability of the device!
FIRMWARE FOR SPI FLASH -----------> FUSION FLTV-32W5, Main: 471-01A3-32202G, Panel: LC320WXE (SB) (B1)
The appearance of the MainBoard 471-01A3-32202G is shown in the figure below:471-01A3-32202G
Main features of the FUSION FLTV-32W5 device:
Installed matrix (LCD panel) LC320WXE (SB) (B1).
The required supply voltage for all nodes of the TV FUSION FLTV-32W5 provides a switching power supply.
MainBoard - the main board (motherboard) is a 471-01A3-32202G module using SPI Flash chips: 24C64; EEPROM: EN25P16; and others.
The tuner CDT-3FP2I2-01 provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: LG Display
Model: LC320WXE-SBB1
Type: a-Si TFT-LCD, Panel
Diagonal size: 31.5 inch
Resolution: 1366x768, WXGA
Display Mode: S-IPS, Normally Black, Transmissive
Active Area: 697.68x392.26 mm
Surface: Antiglare (Haze 10%), Hard coating (3H)
Brightness: 500 cd / m²
Contrast Ratio: 1200: 1
Display Colors: 16.7M (8-bit)
Response Time: 8 (G to G)
Frequency: 60Hz
Lamp Type: 12 pcs EEFL Without Driver
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 12.0V
FUSION FLTV-32W5 TV with LC320WXE LCD display, 32 ”(81 cm) diagonal size in 16: 9 format. 500 cd / m² screen brightness is provided by CCFL (EEFL) fluorescent lamps. Dynamic contrast ratio 4000: 1 is provided by special control of operation illumination depending on the illuminated areas in the plot. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard for graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC. Graphic processing TCA and formation takes place in the digital signal standards 480i, 480p, 576i, 576p, 720p, 1080i.
The power of the acoustic system of sound 20 W (2x10 W) provide two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, S-Video, component, SCART, RGB, VGA, HDMI x2. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768.
The power consumed by the TV working in the network mode is 140 watts.
Overall dimensions: 786x531x110 mm.
The mass of the TV: 16 kg.
Attention! The LC320WXE (SB) (B1) panel of the FUSION FLTV-32W5 LCD TV is its most expensive component.
Avoid hitting the glass and exerting pressure on the screen to avoid permanent damage to the LCD panel!