Technical description and composition of the MYSTERY MTV-3208WH TV, type of panel and applicable modules. The composition of the modules.MYSTERY
Model: MTV-3208WH
Chassis / Version: V4L05
Panel: V315H1-L02
Inverter (backlight): T871029.28
Power Supply (PSU): FSP160-4H02
MainBoard: MSTV3208-ZC01-01
IC MainBoard: CPU: MST6E48RHS-LF-Z1, SPI FLASH: SP25FL032K
Tuner: F21WT-3BAR-E
Control: Service Login: INPUT 2580
Technical Specifications MTV-3208WH
MYSTERY MTV-3208WH
General recommendations for repairing TV LCD
Repair of the MYSTERY TV with the V4L05 chassis should begin with a fault diagnosis, which involves a careful examination of the external and internal elements of the device. Sometimes, based on visible changes in the components of the device, it is possible to draw some conclusions and determine the direction of further troubleshooting even before the necessary measurements are taken. If ring cracks are detected in the soldering of the terminals of the elements or dangling connecting tracks, swollen capacitors or charred resistors - all this can be characteristic signs of the causes or consequences of an already known typical malfunction.
In cases when the MYSTERY MTV-3208WH TV does not turn on, does not respond to the remote control and buttons, no indicators on the front panel light up or blink, and there are no sounds and no signs of operability when turning on, the power module is most likely faulty or there is no power processor on the motherboard (a typical defect of some MYSTERY TVs). First of all, it is necessary to replace the swollen capacitors of the rectifier filters, if any. If the mains fuse is cut off in the power supply, in most cases a breakdown of the power key (s) is detected, which can be integrated with the PWM controller, or a separate field-effect transistor can be used. The rectifier bridge diodes and the electrolytic capacitor of the mains rectifier filter should also be checked.
If a breakdown of the power switch is detected, it should be remembered that in a switching power supply (IIP) it does not fail by itself without any reasons that should be sought by checking other elements of the primary circuit - electrolytic capacitors, a PWM controller, which can only be checked replacement, as well as other semiconductor elements (diodes, transistors, zener diodes).
Sometimes the MYSTERY MTV-3208WH TV does not have an image, but there is sound, or the image appears and immediately disappears. In this case, there is a high probability of a malfunction of the backlight converter, or of the lamps themselves, which can be checked by replacement. In such cases, it is necessary to verify the serviceability of all electrolytic capacitors of the filter according to the power supply of the inverter itself, including in the power supply unit (power supply unit). It is necessary to take into account that in cases of inverter protection shutdown (in order to be able to diagnose) there is a risk of failure of the inverter power elements and take special care. After carrying out repairs, the protection circuit must be restored for further safe operation of the TV.
On the MSTV3208-ZC01-01 motherboard, in case of a malfunction, you should first check the performance of all stabilizers or power converters of the microcircuits and, if necessary, update the software (software). If it is not possible to replace the MB board (SSB), you need to check the health of its elements - CPU: MST6E48RHS-LF-Z1, SPI FLASH: SP25FL032K. Defective components should be replaced.
Attention to the owners! Attempts to repair the TV MYSTERY MTV-3208WH on its own are not recommended by the manufacturer and can lead to serious negative consequences!
SCHEMATIC DIAGRAM / SERVICE MANUAL ------------------> MYSTERY Main MSTV3208-ZC01-01
FIRMWARE FOR SPI FLASH -----------> MYSTERY MTV-3208WH(V4L05), Main MSTV3208-ZC01-01, Panel V315H01-L02
The appearance of the MainBoard MSTV3208-ZC01-01 is shown in the figure below:The motherboard MSTV3208-ZC01-01 is made using the multifunction microprocessor MST6M48RHS-LF, which includes a scaler (graphic controller-scaler). To organize the work of the processor, the external RAM H5PS5162GFR 512Mb DDR2 SDRAM in BGA version and SPI FLASH 25Q32 (4Mb) are used. To provide power to the processor core, a DC / DC converter with an output voltage of 1.2V is used, assembled on the basis of the MP1482 PWM controller. Other nodes of the processor are powered by linear voltage stabilizers 2.5V, 3.3V. 1.8V voltage is used to power the DDR RAM, 3.3V is needed for the SPI FLASH ROM.
It is advisable to start the MainBoard repair by checking the supply voltage in Stand-by mode 5V and 3.3V. In operating mode, check the operation of all linear stabilizers and the DC / DC converter. If there is a backlight and there is no image, you need to check the power of the 5V or 12V panel (depending on the type of LCD panel), which should be present directly on the LVDS connector.
If the indicator signals Stand-by mode and does not respond to the remote control and control buttons, it is recommended to update the SPI Flash software. Taking into account the glitchiness of Winbond SPI chips, it is advisable to replace them with new ones in case of software failures.
MSTV3208-ZC01-01 can be used in TVs:
BBK LEM2648SD (Panel V260B1-LE9 revC1), BBK LEM3248SD (Panel HV320WX2-130 (B3)), BBK LMP3229HDU Ver1 (Panel T315HW02 v.7), BBK LMP3229HDU Ver2 (Panel T315HW04 V7), BBK LEM2649HD (Panel V260H1-LE7 Rev C1), MYSTERY MTV-2607W (Panel V260H1-L05), MYSTERY MTV-3206 (Panel T315XW04 V.7), MYSTERY MTV-3207W (Panel V315B3-L04 rev.c1), MYSTERY MTV-3213LW (Panel T315XW04 V.8), MYSTERY MTV-2220LW (Panel CLAA215FA15), MYSTERY MTV-3207W (Panel HV320WX2-110), MYSTERY MTV-2614LW (Panel V260H1-LE6), MYSTERY MTV-3208WH (Panel V315H1-L02), MYSTERY MTV-2411LW (Panel V236H1-LE5 Rev.C1), MYSTERY MTV-2618LW (Panel V260B2-LE11), MYSTERY MTV-2211LW (Panel CLAA215FA10), MYSTERY MTV-2414LW (Panel V236H1-L01), MYSTERY MTV-2611LW (Panel V260H1-LE6 Rev.C1), MYSTERY MTV-3206W (Panel T315XW03 V.3), MYSTERY MTV-3211LW (Panel V315H3-LE2 Rev. C1), MYSTERY MTV-4207WH (Panel T420HW09 V.1), MYSTERY MTV-1921LD (Panel HT185WX3).
Main features of the MYSTERY MTV-3208WH device:
Installed matrix (LCD panel) V315H1-L02.
To power the backlight used inverter T871029.28.
The formation of the necessary supply voltages for all nodes of the MYSTERY MTV-3208WH TV is carried out by the FSP160-4H02 power supply module, or its analogs.
MainBoard - the main board (motherboard) is an MSTV3208-ZC01-01 module, using CPU chips: MST6E48RHS-LF-Z1, SPI FLASH: SP25FL032K and others.
The F21WT-3BAR-E tuner provides television reception and channel tuning.
Additional technical information about the panel:
Brand: CMO
Model: V315H1-L02
Type: a-Si TFT-LCD, Panel
Diagonal size: 31.5 inch
Resolution: 1920x1080, FHD
Display Mode: Super MVA, Normally Black, Transmissive
Active Area: 698.4x392.85 mm
Surface: Antiglare (Haze 11%), Hard coating (3H)
Brightness: 450 cd / m²
Contrast Ratio: 4000: 1
Display Colors: 16.7M (8-bit), CIE1931 72%
Response Time: 6.5 (G to G)
Frequency: 60Hz
Lamp Type: 4 pcs CCFL Embedded (Inverter)
Signal Interface: LVDS (2 ch, 8-bit), 51 pins
Voltage: 12.0V
MYSTERY MTV-3208WH TV with V315H1-L02 LCD display, 32 "(81 cm) diagonal size in 16: 9 format. 450 cd / m² screen brightness is provided by CCFL (EEFL) fluorescent lamps. Dynamic contrast ratio 4000: 1 is provided by special The design and technical capabilities of the TV provide for viewing broadcasts and films in high quality HD with a resolution of 1920x1080 pixels in a graphic resolution according to the standard 1080p (Full HD). Input high-frequency or video signal can . T be processed by analog systems, PAL, SECAM, NTSC Image processing and generation of the digital signal occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i, 1080p Supported multimedia file formats:. MP3, JPEG.
The power of the speaker system of sound 14 W (2x7 W) provide two speakers. It uses a NICAM stereo signal processing system and Sound Surround.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, S-Video, component, SCART, RGB, VGA, HDMI x2, USB. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768, 1920x1080.
The power consumed by the TV in the operating mode from the network is 150 watts.
Dimensions: With stand 642x444x209 mm, Without stand 570x345x70 mm.