Technical description and composition of the FUSION FLTV-24C10 TV, panel type and applicable modules. The composition of the modules.FUSION LED
Model: FLTV-24C10
Chassis / Version: MS82PT
Panel: LVW230SSOT E1 V2
LED driver (backlight): integrated into MainBoard
PWM LED driver: OB3350CP
Power Supply (PSU): integrated into MainBoard
PWM Power: PWM SOT23-6 LD7536R
MainBoard: TP.MS18VG.P77 MS82PT
IC MainBoard: CPU: MST3M182VGC-LF-TZ, FLASH: GD25Q32BSIG
Tuner: R620D
Technical Specifications FLTV-24C10
FUSION FLTV-24C10
General repair guidelines for TV LCD LED
Repair and diagnostics of any electronic device, in particular FUSION FLTV-24C10, it is advisable to start with a careful external examination of internal and external elements. Sometimes, based on visible changes in the components of the device, it is possible to draw some conclusions and decide on the direction of further troubleshooting even before the necessary measurements are taken. In most cases, the repairman can guess the causes of the defect and possible consequences from the characteristic signs of typical TV defects, for example, ring cracks formed in the soldering of the element leads, swollen rectifier filter capacitors, charred resistors and other circuit elements.
Sometimes the FUSION FLTV-24C10 TV simply does not turn on. No control lights on the front panel are lit or blinking, the TV does not respond to the remote control and does not make any sounds or any signs of life when turned on. The most likely cause of the malfunction is a failure of the common power module. If it is working properly, you need to check the processor batteries on the SSB (Main Board). Diagnostics and repair of the common power supply should always begin with a check of the mains fuse and the condition of the electrolytic capacitors of the secondary rectifier filters. Defective and swollen capacitors should be replaced with new ones. If the fuse is broken, it is advisable to check for a breakdown, first of all, all the power semiconductor elements of the converter and the diode bridge of the rectifier network, as well as the large electrolytic capacitor of the filter of the rectifier network.
Mos-Fet keys used in switching power supplies (SMPS) rarely fail for no reason to look for when checking other circuit elements. Often the breakdown is caused by malfunctions of electrolytic capacitors or semiconductor elements in the primary circuit, or by a break in the resistors in the stabilization circuits. The PWM controller chip may also cause a breakdown of the power switch of the converter.
If the FUSION FLTV-24C10 TV does not have an image, but there is sound, a malfunction in the LED backlight circuits of the LVW230SSOT E1 V2 panel is likely. It is also necessary to check the serviceability of the electrolytic capacitors of the filter of the secondary rectifiers of the PSU (power supply) for excessive ESR.
Often in the absence of backlighting, disassembling the panel is required. It is necessary to check the serviceability of the transitions of the LEDs, as well as the reliability of contact connections in the rulers and connectors.
It should be remembered that it is not possible to determine the break in the LED lines without disassembling the panels using a tester or multimeter without an additional device, for example, a current source. To open all PN junctions connected in series at once, a voltage of several tens of volts may be required.
In cases of attempts to repair the TP.MS18VG.P77 MS82PT motherboard, it is necessary to check the operation of the stabilizers or power converters of its microcircuits and, if possible, update the software (software). BGA chips can in most cases be diagnosed by local heating.
Board repair and replacement of CPU chips: MST3M182VGC-LF-TZ, FLASH: GD25Q32BSIG are carried out with the necessary equipment, and the corresponding element base. Malfunctions associated with the application of the soldering technology of the BGA processor can be localized by the heating method.
Attention to the owners! Attempts to self-repair the FUSION FLTV-24C10 TV are not recommended by the manufacturer and can lead to serious negative consequences!
FIRMWARE FOR SPI FLASH -----------> FUSION FLTV-24C10, Main: TP.MS18VG.P77 MS82PT, Panel: LVW230SSOT E1 V2
If a failure occurs in the SPI FLASH software from Winbond, we recommend that you replace the chip with a new one. Often, unreadable Winbond microcircuits can temporarily restore their functionality after a strong temperature exposure, for example, heating with a soldering station or a lighter. Sometimes this is enough to read its regular contents.
Repair MainBoardThe appearance of MainBoard TP.MS18VG.P77 is shown in the figure below:
TP.MS18VG.P77
TP.MS18VG.P77 can be used in TVs:
ERISSON 24LET35 (Panel LVW240CMOT E1 V2), ERISSON 19LET35 (Panel M185XTN01.3), FUSION FLTV-24C10 (Panel LVW230SSOT E1 V2), FUSION FLTV-32C10 (Panel LVW320CSOT E81 V7), HYUNDAI H-LED32V19 (Panel LVW320CSOT E45 V10), HYUNDAI H-LED32V23 (Panel LVW320C80T E64 V5), TCL 19T2100 (Panel M185XTN01.2), TELEFUNKEN TF-LED32S23 (Panel LVW320CS0T E146 V1), THOMSON 32B2600 (Panel LVW320C8OT EB1), THOMSON 28B2500 (Panel LVW280CSOT E13V1).
Main features of the FUSION FLTV-24C10 device:
Installed matrix (LED-panel) LVW230SSOT E1 V2.
To power the backlight LEDs, a converter is used, combined with the main board TP.MS18VG.P77, controlled by the OB3350CP PWM controller.
The power module is combined with the MainBoard and is designed according to a flyback AC / DC voltage converter using PWM SOT23-6 LD7536R microcircuits.
MainBoard - the main board (motherboard) is a TP.MS18VG.P77 module, using CPU chips: MST3M182VGC-LF-TZ, FLASH: GD25Q32BSIG and others.
The R620D tuner provides television reception and channel tuning.
FUSION FLTV-24C10 TV with LVW230SSOT LCD display, 24 "(61 cm) diagonal size in 16: 9 format. The required screen brightness of 280 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 60,000: 1 is achieved by special control of the LEDs. The LED panels of this TV are equipped with edge LED backlighting - Edge LED. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard for graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i Supported media file formats: MP3, JPEG.
The power of the sound system 10 W (2x5 W) provides two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, VGA, HDMI, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
Overall dimensions: with stand 544x385x162 mm, without stand 544x342x54 mm.
TV Weight: with stand: 3.7 kg, without stand: 3.45 kg.
Attention! The LVW230SSOT E1 V2 panel of the FUSION FLTV-24C10 LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.