Friday, 3 July 2020

REPAIR / SERVICING TV FUSION FLTV-32H20B

Technical description and composition of the FUSION FLTV-32H20B TV, panel type and applicable modules. The composition of the modules.
FUSION LED
Model: FLTV-32H20B
Chassis / Version: T.MS18VG
Panel: LM315TA-T01
Power Supply (PSU): Adapter 12V
MainBoard: T.MS18VG.81B 12145
IC MainBoard: SPI FLASH: Winbond 25Q32
Tuner: CDT-3SP512-36
Technical Specifications FLTV-32H20B
FUSION FLTV-32H20B
General repair guidelines for TV LCD LED
It is advisable to start the repair of the FUSION FLTV-32H20B TV with a careful external examination of both internal and external elements. In some cases, visible external damage to the elements can suggest the direction of troubleshooting and localization of the defect even before the start of the necessary measurements at the control points of the nodes of electronic circuits. Carbonized paint on the upper layer of resistors, electrolytic capacitors of rectifier filters swollen after boiling, cracked soldering at the terminals of heating elements or transformers can often suggest the cause of the defect and possible consequences.
Malfunctions of the power module can be expressed in different ways, for example, the FUSION FLTV-32H20B does not turn on at all and the control lights on its front panel do not light up and do not blink, there are no signs of operability. It should be noted that with the same external manifestations, the processor power regulator (converter) may be faulty. First of all, it is necessary to replace the swollen capacitors of the rectifier filters, if any. If the mains fuse is broken in the power supply, in most cases a breakdown of the power key (s) is detected, which can be integrated with the PWM controller, or a separate field-effect transistor can be used. The rectifier bridge diodes and the electrolytic capacitor of the mains rectifier filter should also be checked.
It should be borne in mind that in the practice of repair it is extremely rare that key transistors in switching power supplies (SMPS) fail for no reason that should be sought by checking other components, for example, a breakdown of the key can provoke faulty elements of the damper circuits, or dried electrolytic capacitors or dangling primary resistors BP circuits involved in the stabilization process. In this case, all semiconductor elements of the binding of the PWM controller microcircuit are subject to verification, which it is desirable to verify by replacement.
If the FUSION FLTV-32H20B has no image, but there is sound and the TV is controlled by the remote control, a malfunction in the backlight circuits of the LM315TA-T01 panel is likely. The LEDs or the power converter - LED driver may be faulty. Often in such cases, when you turn on the TV, an image appears and immediately disappears. First of all, it is necessary to verify the operability of the electrolytic capacitors of the rectifier filter supplying the LED driver, and check the LEDs, connecting obviously known good diagnostics.
To check the health of the LEDs, as well as contact connections in the ruler circuit, it is necessary to disassemble the panel.
It is impossible to check the LED line for breaks without disassembling the panel with a multimeter or tester. For these purposes, it is necessary to open all series-connected PN junctions and a voltage of the order of tens of volts will be required, and ideally, a current source.
On the T.MS18VG 81b 12145 motherboard, in case of a malfunction, you should first check the performance of all stabilizers or power converters of the microcircuits and, if necessary, update the software (software).
In some cases, it is necessary to check or replace (if necessary) the elements of the MB board (SSB) - SPI FLASH: Winbond 25Q32. In cases where the BGA processor is used, its malfunction is usually detected by local heating.
If the TV works normally from external devices, but does not tune to television channels, the tuner CDT-3SP512-36 may be malfunctioning. In such cases, first of all, you should make sure that there are supply voltages at its corresponding terminals, as well as the power supply of varicaps (30-33V).
Remember! Attempts to self-repair by users of the FUSION FLTV-32H20B TV without the appropriate qualifications and necessary experience can lead to serious negative consequences!


FIRMWARE FOR SPI FLASH  ----------->   FUSION FLTV-32H20B, Main: T.MS18VG 81b 12145, Panel: LM315TA-T01



In the event of a failure in the software of the SPI FLASH chip from Winbond, we recommend that you replace it with a new one. Sometimes faulty SPI Winbond microcircuits can be restored for a while after a soldering station is heated by a hairdryer. Usually this is enough to read its contents.
Repair MainBoard
The appearance of MainBoard T.MS18VG.81B is shown in the figure below:
T.MS18VG.81B
T.MS18VG.81B can be used in TVs:
AKAI LEA-32V07P (Panel T315XW06 V.0), BBK LEM3283 V1.0 (Panel LC320EXN SDA1), BBK LEM3283F (Panel V315H3-LE4 Rev.C1), ERISSON 42LEN60 (Panel LC420EUN), ERISSON 32LEN60 (Panel LTA320AN01 D02 ), FUSION FLTV-32H20B (Panel LM315TA-T01), SUPRA STV-LC3217W (Panel LC320WXE-SBV1), SUPRA STV-LC3217AWL STV-LC3217W (Panel HV320WX2-201), SUPRA STV-LC3277W (Panel HV320WX2-201), SUPRA STV-LC32170F (Panel HK315TVM-HHC9H).
Main features of the FUSION FLTV-32H20B device:
Installed matrix (LED-panel) LM315TA-T01.
To power all internal nodes of the FUSION FLTV-32H20B TV, an external adapter 12V type is used.
MainBoard - the main board (motherboard) is a T.MS18VG.81B module, using SPI FLASH chips: Winbond 25Q32 and others.
The tuner CDT-3SP512-36 provides the reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: PANDA
Model: LM315TA-T01
Type: a-Si TFT-LCD, CELL
Diagonal size: 31.5 inch
Resolution: 1366x768, WXGA
Display Mode: ASV, Normally Black, Transmissive
Active Area: 697.685x392.256 mm
Surface: Antiglare, Hard coating (2H)
Glass Depth: 0.70 + 0.70 mm
Transmissivity: 4.9% (with Polarizer)
Contrast Ratio: 3000: 1
Display Colors: 16.7M (8-bit), CIE1931 72%
Response Time: 7 (G to G)
Frequency: 60Hz
Signal Interface: LVDS (1 ch, 8-bit), 30 pins
Voltage: 12.0V
FUSION FLTV-32H20B TV with LM315TA-T01 LCD, 32 "(81 cm) diagonal size in 16: 9 format. The required screen brightness of 450 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 80000: 1 is achieved by special control of the LEDs The LED-panel of this TV is equipped with LED end-lighting - Edge LED. You can view images in high quality HD at a resolution of 1366x768 pixels in the standard for graphic decomposition 720p (HD Ready). The input high-frequency or video signal can be processed in analogue systems PAL, SECAM , NTSC. Graphic processing and digital signal generation occurs in the standards 480i, 480p, 576i, 576p, 720p, 1080i. Supported media file formats: MP3, JPEG.
The power of the sound system 12 W (2x6 W) provides two speakers. The audio processing system NICAM STEREO is used.
The external interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, VGA, HDMI x3, USB. An output for connecting headphones is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector is used on the TV case, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
A digital tuner is capable of receiving television channels in DVB-T standards.
Overall dimensions: with stand 794x561x204 mm, without stand 794x500x90 mm.
TV Weight: with stand: 9.1 kg, without stand: 8.6 kg.
Attention! The panel of the LM315TA-T01 FUSION FLTV-32H20B LED TV is an expensive and unreliable element.
Avoid any impact on the glass and pressure on the surface of the screen to avoid damage to the LED panel!
It is also unsafe to get liquid on the screen. Sometimes one drop is enough if it flows down the glass onto the cables so that the TV becomes unrepairable.