Technical description and composition of the DNS H32A30 TV, panel type and modules used. The composition of the modules.DNS LED
Model: H32A30
Chassis / Version: TP.VST59S.P89
Panel: JHD315GH-E52
LED backlight: 75YYN11003-PILB67F7-E510-B-PJL
LED driver (backlight): integrated into MainBoard
PWM LED driver: OB3350CP
Power Supply (PSU): integrated into Mainboard
PWM Power: PWM SOT23-6
MOSFET Power: MDF7N60B
MainBoard: TP.VST59S.P89
IC MainBoard: Cpu: TSUMV59XES-XG, Spi Flash: W25Q32
Tuner: R620D
Specifications H32A30
DNS H32A30
General recommendations for TV LCD LED repair
Possible manifestations of malfunctions
- DNS H32A30 does not turn on, LEDs on the front panel are off or flashing. The TV does not respond to the control buttons and the remote control.
A malfunction in such cases, first of all, should be looked for in the power elements of a switching power supply (SMPS) - a mains voltage converter (AC / DC), which in this TV model is combined with the main board MainBoard TP.VST59S.P89. It is necessary to measure its secondary output voltages, and if they are absent, check the power switches (MDF7N60B) and rectifier diodes in the converters for a short circuit.
In case of breakdowns of semiconductors in the secondary circuits of any converter, as a rule, it can operate in an emergency mode of short circuit without output voltages, and with a short circuit in the elements of the primary circuit, the mains fuse most often breaks off immediately and less often the current sensor in the source of the key.
Breakdown of Mos-Fet switches used in switching power supplies is often caused by malfunctions of other elements, for example, in the power supply circuit of a PWM controller, in frequency setting or damper circuits, as well as in negative feedback stabilization. PWM microcircuits (PWM) PWM SOT23-6 are usually checked by replacing them with new ones, or knowingly working.
- There is no picture, but there is sound and reaction to the remote control. Or, for a second, the image may appear immediately after switching on.
Usually, in such cases, a malfunction is detected in the LED panel backlight nodes. The reason may be both in the power supply of the LEDs, in their serviceability (breakdown or breakage), as well as in the violation of the contact connections of the LED strips.
To identify an open circuit in the LED lines without disassembling the panel, a current source is required. It is impossible to open the junctions connected in series with a simple multimeter; a voltage of several tens of volts is required.
- The TV does not go into operation, does not respond to the remote control. The indicator on the front panel is on or blinking.
Repair or diagnostics of the TP.VST59S.P89 motherboard should begin with checking the stabilizers and power converters necessary to power the microcircuits and matrix. If necessary, you should update or replace the software (software). If it is not possible to replace the MB (SSB) board, you must check the serviceability of its elements - Cpu: TSUMV59XES-XG, Spi Flash: W25Q32. Defective components must be replaced.
The malfunction of the R620D tuner is established after checking the software and all supply voltages at its terminals. The data exchange of the tuner with the processor via the I2C bus can be monitored with an oscilloscope.
Attention! Users and owners of H32A30 TVs who do not have the appropriate qualifications, knowledge and experience are strongly discouraged from trying to repair themselves in order to avoid negative consequences that can lead to the complete non-repairability of the device.
DOWNLOAD FIRMWARE FOR SPI FLASH -----------> DNS H32A30, Main: TP.VST59S.P89, Panel: JHD315GH-E52
The appearance of MainBoard TP.VST59S.P89 is shown in the figure below:TP.VST59S.P89
TP.VST59S.P89 motherboard is combined with a power supply module and is an independent device based on the TSUMV59Xxx multifunctional processor. Repair of such a board must begin with checking the power supply elements, as well as the operability of voltage converters and linear stabilizers necessary to provide power to certain processor nodes, in particular: core power supply + 1.2V, built-in DDR + 1.8V memory and stand-by mode node by 3.3V. The supply voltage of the LCD panel is 5V or 12V, depending on the type of panel used, it is necessary to check directly on the LVDS connector.
TP.VST59S.P89 can be used in TVs:
AKAI LEA-32A08G (Panel LC320EXN (SE)(E1)), AKAI LEA-28A08W (Panel ST2751A01-1), DEXP 32A3300 (Panel JHD315GH-E52), DNS H32A30 (Panel JHD315GH-E52), FUSION FLTV-32L42B (Panel KM315E3-CS-02), TELEFUNKEN TF-LED32S6 (Panel CX315DLEDM ST3151A05-5).
Main features of the DNS H32A30 device:
Installed matrix (LED panel) JHD315GH-E52.
To power the backlight LEDs, a converter combined with the TP.VST59S.P89 main board is used, controlled by the OB3350CP PWM controller.
The power module is combined with the MainBoard and is made according to the AC / DC flyback voltage converter using SOT23-6 PWM microcircuits and MDF7N60B power switches.
MainBoard - the main board (motherboard) is a TP.VST59S.P89 module, using Cpu chips: TSUMV59XES-XG, Spi Flash: W25Q32 and others.
The R620D tuner provides reception of television programs and tuning to channels.
H32A30 DNS TV with LCD JHD315GH-E52, 32 "(81 cm) 16: 9 format. Dynamic contrast ratio 5000: 1 is achieved by special control of LED operation depending on the illumination of areas in the scene. This model uses a panel with an end the location of the backlight LEDs - Edge LED.
The JHD315GH-E52 sensor and the MainBoard software TP.VST59S.P89 provide high quality HD image viewing at a resolution of 1366x768 pixels in 720p (HD Ready). The input high-frequency or video signal is decoded in analog systems PAL, SECAM, NTSC. Graphic processing and formation of a digital signal occurs in the 480i, 480p, 576i, 576p, 720p, 1080i standards. Supported media file formats: MP3, MPEG4, MKV, JPEG. Stereo sound is provided by two built-in speakers. The NICAM STEREO audio processing system is used.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, VGA, HDMI x2, USB. A headphone output is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector on the TV case is used, this interface supports resolutions: 640x480, 800x600, 1024x768, 1360x768.
The TV uses a power supply unit as part of the MainBoard.
Dimensions: With stand 720x520x220 mm, Without stand 720x460x80 mm.
Attention! Panel JHD315GH-E52 LED TV DNS H32A30 is an expensive and unreliable element.
Do not allow any impact on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV unrepairable.