Technical description and composition of the ROLSEN RL-24L1003F TV, panel type and modules used. The composition of the modules.ROLSEN LED
Model: RL-24L1003F
Chassis / Version: RSAG7.820
Panel: V236H1-LE2 Rev. C1 LED
LED driver (backlight): RSAG7.820.2256 Ver.D
PWM LED driver: OZ9998GN (24)
Power Supply (PSU): RSAG7.820.2256 Ver.D
PWM Power: NCP1271A (8),
MOSFET Power: W15 / 10 BCP56, 3N80
MainBoard: RSAG7.820.2280 / ROH
IC MainBoard: MT8223LFMU, CD1517CP, SPI FLASH: MX25L1606E
Tuner: HFT2-8C6 / V116H
Control: ER-31607R
RL-24L1003F Specifications
ROLSEN RL-24L1003F
General recommendations for TV LCD LED repair
It is advisable to start repairing the ROLSEN RL-24L1003F TV with a careful external examination of both internal and external elements. Visible damage to elements can sometimes indicate the direction of searching for a defect even before the necessary measurements are taken. Experienced repairmen often guess about the causes of the defect and the possible consequences, for example, by ring cracks in the soldering of the element terminals, as well as by swollen capacitors or resistors burnt out to coal dust and other external indirect signs.
In the absence of any signs of operability, when the ROLSEN RL-24L1003F does not turn on and does not signal anything with the control lamps on the panel, there is a possibility of a malfunction of the RSAG7.820.2256 Ver.D TV power module. With the same manifestations, the power regulator of the control processor on the motherboard may be faulty. When repairing a power supply, it is advisable to start diagnostics with checking the mains fuse and electrolytic capacitors of the filters of the secondary rectifiers of the converter. In the event of a break in the fuse, the cause should be sought in the power semiconductor elements of the pulse converter of the main power supply unit. First of all, it is necessary to check the diodes of the rectifier bridge of the mains voltage and the power switch (keys) of the W15 / 10 BCP56, 3N80 converter.
As a rule, switches in switching power supplies (SMPS) are quite reliable and rarely fail without reasons that should be looked for by checking other components of the circuit - electrolytic capacitors, resistors and semiconductor elements of the primary circuit. The PWM microcircuit is checked by replacing it with a known good one.
If, when ROLSEN RL-24L1003F is turned on, there is no image, or it appears for a second and disappears, but there is sound, most likely there is a malfunction in the V236H1-LE2 Rev. C1 LED panel backlight LED circuit, or in their power converter. It is necessary to check the electrolytic capacitors of the filter of the secondary rectifiers in the common power supply.
A malfunction in the backlight circuits often occurs due to an open circuit in the power supply circuit of the LED lines. It is required to disassemble the panel and check the LEDs themselves, the ration of their conclusions, as well as the reliability of the connections in the connectors and the ration of the connector pins.
When trying to detect a break in the LED lines, it should be borne in mind that it is difficult to do this without disassembling the panel. For example, a current source is required to open PN junctions connected in series.
On the RSAG7.820.2280 / ROH motherboard, in the event of a malfunction, you should first check the operability of all stabilizers or power converters of microcircuits and, if necessary, update the software (software).
When repairing an MB board, you need to check its components MT8223LFMU, CD1517CP,. Defective elements should be replaced. If BGA chips are installed, their failure is usually localized by warming up.
If you suspect a malfunction of the HFT2-8C6 / V116H tuner, first of all, you need to make sure that there is a supply voltage of the varicaps (30-33V) at the corresponding output of the tuner, as well as other voltages supplying it.
Attention to the owners! Attempts to self-repair the ROLSEN RL-24L1003F TV are not recommended by the manufacturer and can lead to serious negative consequences!
DOWNLOAD FIRMWARE FOR SPI FLASH -----------> ROLSEN RL-24L1003F, Main: RSAG7.820.2280/ROH, Panel: V236H1-LE2 Rev.C1 LED
The appearance of the MainBoard T.VST29.A2B_12313 is shown in the figure below:T.VST29.A2B_12313
T.VST29.A2B_12313 can be used in TVs:
DNS E19A00 (Panel CX185LEDM (V185B1-PE)), DNS E22A11 (Panel M215HGE-P02), DNS E22A00 (Panel CX215LEDM M215HGE-P01), DNS E16A20 (Panel TL156WH4 (TL)(N2)), ERISSON 24LEB15 (Panel M240HW01 VD), ROLSEN RL-19L1003U (Panel M185BGE-L10 Rev.C1), ROLSEN RL-22L1003U (Panel V216BG1-LE1 REV C1), ROLSEN RL-23L1003UF (Panel M230HGE-L20 Rev.C1), ROLSEN RL-23L1005UF (Panel M230HGE-L20 RevC1).
External view of the power supply
Main features of the ROLSEN RL-24L1003F device:
Installed matrix (LED-panel) V236H1-LE2 Rev. C1 LED.
To power the backlight LEDs, the RSAG7.820.2256 LED driver is used, controlled by the OZ9998GN PWM controller (24).
The formation of the necessary supply voltages for all nodes of the ROLSEN RL-24L1003F TV is carried out by the RSAG7.820.2256 power module, or its analogs using NCP1271A microcircuits (8), and power switches of the W15 / 10 BCP56, 3N80 type.
MainBoard - the main board (motherboard) is an RSAG7.820.2280 module, using MT8223LFMU, CD1517CP, SPI FLASH: MX25L1606E and others.
The HFT2-8C6 / V116H tuner provides reception of television programs and tuning to channels.
Additional technical information about the panel:
Brand: CMO
Model: V236H1-LE2
Type: a-Si TFT-LCD, Panel
Diagonal size: 23.6 inch
Resolution: 1920x1080, FHD
Display Mode: TN, Normally White, Transmissive
Active Area: 521.28x293.22 mm
Surface: Antiglare (Haze 25%), Hard coating (3H)
Brightness: 300 cd / m²
Contrast Ratio: 1000: 1
Display Colors: 16.7M (8-bit), CIE1931 70%
Response Time: 1.5 / 3.5 (Tr / Td)
Frequency: 60Hz
Lamp Type: 12S8P WLED Without Driver
Signal Interface: LVDS (2 ch, 8-bit), 30 pins
Voltage: 5.0V
ROLSEN RL-24L1003F TV with LCD V236H1-LE2, diagonal size 24 "(61 cm) 16: 9 format. The required screen brightness of 300 cd / m² is provided by LED backlighting. Dynamic contrast ratio of 80000: 1 is achieved by special control of LED operation The LED panel of this TV is equipped with Edge LED backlighting.The design and technical capabilities of the TV provide viewing of broadcasts and films in high quality HD at a resolution of 1920x1080 pixels in graphic resolution in the standard 1080p (Full HD) .Input high-frequency or video signal can be processed in analog systems PAL, SECAM, NTSC Graphic processing and digital signal formation occurs in 480i, 480p, 576i, 576p, 720p, 1080i, 1080p standards Supported multimedia file formats: MP3, WMA, JPEG.
The power of the acoustic system of sound 4 W (2x2 W) is provided by two speakers. The NICAM STEREO audio processing system is used.
External interface (communication with other devices) is supported by standard input and output connectors: antenna input (RF), AV, audio x2, component, SCART, VGA, HDMI, USB. A headphone output is provided. To connect a computer or laptop to this TV model, a VGA (D-Sub 15) connector on the TV case is used, this interface supports resolutions: 640x480, 800x600, 1024x768.
The power consumed by the TV in operating mode from the network is 30 W.
Dimensions: with stand 564x471x207 mm, without stand 564x370x44 mm.
TV weight: 4.6 kg.
Attention! Panel V236H1-LE2 Rev. C1 LED-TV ROLSEN RL-24L1003F is an expensive and unreliable element.
Do not allow any impact on the glass and pressure on the screen surface to avoid damage to the LED panel!
It is also unsafe for liquid to spill onto the screen. Sometimes one drop is enough if it drips down the glass onto the cables to make the TV unrepairable.